manualshive.com logo in svg

Holtek BS86DH12C, Manual, Page: 126 / 192

Share
Download
Holtek BS86DH12C Manual Download Page 126

Rev. 1.00

126

October 26, 2018

Rev. 1.00 

127

October 26, 2018

BS86DH12C

High Voltage Touch A/D Flash MCU with HVIO

BS86DH12C

High Voltage Touch A/D Flash MCU with HVIO

Step6. Restore the comparator input offset calibration value V

COS

 into the OCPCOF[4:0] bit field. 

The offset Calibration procedure is now finished.
Where V

COS

=(V

COS1

+V

COS2

)/2

Note: S4 is on and the D/A converter is off. This situation is only available for comparator calibration 

procedure. In the normal operation mode, S4 is off.

Over Voltage Protection – OVP

The device includes an over voltage protection function which provides a protection mechanism for 
applications. The input voltage on the OVPI0 or OVPI1 pin is compared with a reference voltage 
generated by an 8-bit D/A converter. When a preset voltage condition occurs, an OVP interrupt will 
be generated if the corresponding interrupt control is enabled.

-

+

AV

DD

OVPI0

CMP

OVPEN

OVPDA[7:0]

HYS[1:0]

OVP interrupt

Debounce

OVPDEB[2:0]

OVPO

OVPSPOL

OVPI1

OVPS[1:0]

OVPCOUT

f

SYS

OVPCOUT

S1

S0

S2

1

1

ON OFF ON

OVPCOFM OVPCRS S0 S1

x
0

0
1

S2

ON

OFF

ON
ON

OFF

ON

x: Don't care

8-bit 

DAC

Note: As the OVP function relevant external pins are pin-shared with general I/O or other functions, before using 

the OVP function, make sure the corresponding pin-shared function registers be set properly.

Over Voltage Protection Circuit

Over Voltage Protection Operation

The OVP circuit is used to prevent the input voltage from being in an unexpected level range. The 
voltage can be sourced from the OVPI0 or OVPI1 pin which is determined by the OVPS1~OVPS0 
bits in the OVPC2 register. The selected OVP input voltage is compare with a reference voltage 
provided by an 8-bit D/A converter. The 8-bit D/A converter reference input signal is supplied by 
the positive power supply, AV

DD

. The comparator output, OVPCOUT, will first be filtered with a 

certain de-bounce time period selected by the OVPDEB2~OVPDEB0 bits in the OVPC0 register. 
Then a filtered OVP digital comparator output, OVPO, is obtained to indicate whether a user-defined 
voltage condition occurs or not. 
If the OVPSPOL bit is cleared to 0 and the comparator inputs force the OVPO bit to change from 
0 to 1, or if the OVPSPOL bit is set to 1 and the comparator inputs force the OVPO bit changes 
from 1 to 0, the corresponding interrupt will be generated if the relevant interrupt control bit is 
enabled. Therefore, the OVPSPOL bit must be properly configured according to user’s application 
requirements. The comparator in the OVP circuit also has hysteresis function controlled by the 
HYS1~HYS0 bits.
Note that the debounce clock, f

DEB

, comes from the system clock, f

SYS

. The D/A converter output 

voltage is controlled by the OVPDA register, the D/A converter output is defined as below:

DAC V

OUT

=(D/A converter reference voltage/256)×OVPDA[7:0]

Summary of Contents for BS86DH12C

































































































































































































Reviews:

No comments