Hofmann Megaplan megaline SSENCE Series Service Manual Download Page 45

Page: 45 / 52

Hofmann Megaplan Service Manual megaline SSENCE

SSENCE 400/600

Page 44 of 52

6.6 Switch from Automatic to Manual (Camera bar - only 600)

It is possible on the SSENCE 600 to switch from automatic movement by software to a manual

movement by hand. If switched to manual the movements of the arm will be done by the switch

on the right side of the chassis.

Automatic installation:

The power for movement of the arm is coming over cable no. 4 from camera control board.

This is plugged on the little bridge board. Here are the two versions:

Old Version: New Version

If the cable Nr. 4 from camera board is connected

the Automatic adjustment is installed.

Manual installation.

there is a second cable nr. 4 installed in the machine.

Switch machine off. Unplug the cable shown on automatic installation and plug this onto that

board instead of the old one.

Switch machine on. Even without computer you can adjust the height of the camera bar by

switch. This can be done for example if the software controller does not work anymore.

Correct installed manual switch.

Summary of Contents for megaline SSENCE Series





















































Search results

Summary of Contents for megaline SSENCE Series

Reviews:

Related manuals for megaline SSENCE Series

Brands by name

Popular brands

Hofmann Megaplan megaline SSENCE Series, Service Manual

Search results

Summary of Contents for megaline SSENCE Series

Reviews:

Related manuals for megaline SSENCE Series

Brands by name

Popular brands