Hofmann Megaplan megaline SSENCE Series Service Manual Download Page 42

Page: 42 / 52

Hofmann Megaplan Service Manual megaline SSENCE

SSENCE 400/600

Page 41 of 52

AFTER DOWNLOAD:

Be sure that the dongle is plugged into a USB-port and the red LED is on.

Otherwise contact Hofmann Megaplan.

Installation of Basic Software

•

Go to your download folder and start installation by double click

SSENCE software (version number).exe

•

Setup starts to install the Basic Software

Follow the steps of the installation routine (always confirm)

•

After complete installation the SSENCE program is starting.

•

Close the SSENCE program to go on with database installation

For the password to extract the database files contact Hofmann Megaplan.

Installation of Database

•

Start Database installation by double click.

•

Type in password you got from Hofmann Megaplan.

•

Always confirm - folder will be selected automatically.

•

After Installation start SSENCE Software

•

It can be that the software can not find the correct links to the database on first start.

•

If that is the case please shut down and restart SSENCE Software.

•

Check if databases are present and activate the database you need. (By Setup - please refer

manual)

Summary of Contents for megaline SSENCE Series





















































Search results

Summary of Contents for megaline SSENCE Series

Reviews:

Related manuals for megaline SSENCE Series

Brands by name

Popular brands

Hofmann Megaplan megaline SSENCE Series, Service Manual

Search results

Summary of Contents for megaline SSENCE Series

Reviews:

Related manuals for megaline SSENCE Series

Brands by name

Popular brands