background image

13  EC Directive 

Operation manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex 

84

 

Technische Änderungen ohne Vorankündigung vorbehalten

 

Last update: October 2016

 

13

 

EC Directive 

A Directive or EC Directive is a legal instrument of the European Community 

addressing at the member states and forcing them to implement specific 

regulations or targets. Leastwise, micro annular gear pumps are covered, by the 

scope of application of the following Directives: The following directives are of 

importance for the user of the described micro annular gear pumps: 

Low-Voltage Directive (2014/35/EC) 

The Low-Voltage Directive is not relevant for micro annular gear pumps 

described in this manual, because the supply voltage is limited to a maximum 

of 30 VDC. 

Machinery Directive (2006/42/EC) 

A micro annular gear pump is a machine and is consequently covered by this 

Directive. However, it may be a part of a machine or installation. 

EMC Directive (2014/30/EU) 

The Directive on Electromagnetic Compatibility (EMC) applies to all electronic 

and electrical devices, installations and systems. Consequently, the Motion 

Controller of the micro annular gear pump is covered by the EMC Directive. 

RoHS Directive 

(

2002/95/EC) 

To our knowledge our products delivered to you do not contain substances or 

applications in concentrations that are forbidden by this directive. No 

substances contain our products delivered to you after our current knowledge 

in concentrations or application, the placing on the market in products 

according to the valid requirements forbade to the Directive. 

WEEE Directive (2002/96/EC) 

 

Disposal of micro annular gear pumps has to be environmentally sound. 
All materials and liquids haveto be recycled in accordance with the relevant 

regulations. Electrical parts can not be disposed of as household waste. They 

have to be delivered to designated collection points. 
 

Summary of Contents for mzr-2509 Ex





























































































































Reviews: