HNP Mikrosysteme mzr-2509 Ex Operating Manual Download Page 37

Page: 37 / 124

5 Modular system

Operating manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

Last update: October 2016

Technische Änderungen ohne Vorankündigung vorbehalten.

The equipment fulfils the requirements to that temperature class T3.

For the safe employment of the equipment within highly

combustible ranges special conditions are to be considered.

5.3.1

Construction materials of heating- and cooling module

Wetted parts

mzr-2909 Ex, mzr-4609 Ex

mzr-7209 Ex

Pump case material

stainless steel 316L (1.4404)

stainless steel 316L (1.4404, 1.4435)

table 13

Construction materials of the wetted parts

The resistance of the construction materials to the delivered liquids should be

verified by the operator for each individual application of the heating and

cooling module.

The chemical resistance of seals in each individual must be verified by the

operator.

5.4

Gas-tight seal module

Micro annular gear pumps are „technical tight“, but not hermetical tight. That

means there is a small possibility of gas or liquid coming out from inside of the

pump or also penetrating into the pump between the inner plates of the

structure. These plates have a super finish surface so that they are tight when

layered over each other.

For the Ex-pump additional O-rings are mounted between the plates to

increase the safety of thightness. With the gas-tight module and the fluidic seal

module micro annular gear pumps are nearly hermetical tight.

The micro annular gear pumps mzr-2909 Ex, mzr-4609 Ex and mzr-7209 Ex will

be delivered in a gas-tight version in every case.

Summary of Contents for mzr-2509 Ex





























































































































Search results

Summary of Contents for mzr-2509 Ex

Reviews:

Related manuals for mzr-2509 Ex

Brands by name

Popular brands

HNP Mikrosysteme mzr-2509 Ex, Operating Manual

Search results

Summary of Contents for mzr-2509 Ex

Reviews:

Related manuals for mzr-2509 Ex

Brands by name

Popular brands