HNP Mikrosysteme mzr-2509 Ex Operating Manual Download Page 29

Page: 29 / 124

4 Description of the pump

Operating manual mzr-2509 Ex/ mzr-2909 Ex / mzr-4609 Ex / mzr-7209 Ex

Last update: October 2016

Technische Änderungen ohne Vorankündigung vorbehalten.

4.2

Construction

The micro annular gear pumps mzr-2509 Ex, mzr-2909 Ex, mzr-4609 Ex and

mzr-7209 Ex consist out pump head, coupling assembly and motor with cable

gland. The micro annular gear pump has a bracket to the simple fastening.

cable gland

motor

bracket

coupling assembly

pump head

outlet

inlet

figure 13

Design of the micro annular gear pumps mzr-2909 Ex and mzr-4609 Ex (mzr-7209 Ex similar illustration)

4.3

Materials and liquids

Wetted parts

mzr-2909 Ex, mzr-4609 Ex

mzr-7209 Ex

Pump housing

stainless steel 316 L (1.4404, 1.4435) stainless steel 316 L (1.4404, 1.4435)

Rotors, shaft, bearing

tungsten carbide Ni-based

Shaft sealing

graphite-reinforced PTFE,
316L spring

Static sealing

FKM,
optional: EPDM, FFKM

table 10

Construction materials of the wetted parts

The liquid resistance of the materials has to be checked and guaranteeing

before the operation by the operator.

The liquid resistance has to be checked in every individual case. The feeding of

non-lubricant liquids reduces the service life of the micro annular gear pump.

This is also true for liquids containing particles.

Summary of Contents for mzr-2509 Ex





























































































































Search results

Summary of Contents for mzr-2509 Ex

Reviews:

Related manuals for mzr-2509 Ex

Brands by name

Popular brands

HNP Mikrosysteme mzr-2509 Ex, Operating Manual

Search results

Summary of Contents for mzr-2509 Ex

Reviews:

Related manuals for mzr-2509 Ex

Brands by name

Popular brands