HMS Networks Intesis DALI User Manual Download Page 8

Page: 8 / 34

Intesis

KNX

– DALI

User Manual r1.1 EN

This information is subject to change without notice

URL

http

://www.intesis.com

8 / 34

KNX Comunication Objects

2.3.1 Single DALI device signals

There are up to 94 signals for each DALI device or ballast.

Supported signals vary according to device type, configured through Intesis MAPS.
Following abbreviations are done in the table:

•

FL: Fluorescent light (device type 0)

•

EML: Emergency light (device type 1)

•

LED: LED module (device type 6)

TOPIC

Ballast /

Device Type

NAME

LEN

DATAPOINT TYPE

FLAGS

FUNCTION

DPT_NAME

DPT_ID

COMM

ERR

Ballast / Lamp Failure

1 bit

DPT_Alarm

1.005

0-OK
1-Ballast / Lamp Failure

x Update All ECG Status

DPT_Switch

1.001

0-Update Finished
1-Trigger Update

x Ballast Status

1 byte

Unsigned Value

5.x

b7-PwrCycle
b6-MissShAdd
b5-ResetSt
b4-FadeRun
b3-BallLimErr
b2-LampPwrOn
b1-LampFail
b0-BallFail

x Actual Level

1 byte

DPT_Scaling

5.001

0 to 100 %

FLAGS:

If marked with a

black

", it will be enabled by default and couldn't be disabled.

If marked with

red

, column will be disabled by default but could be enabled by user.

If marked with

blue

, column will be enabled by default but could be disabled by user.

Summary of Contents for Intesis DALI



































Search results

Summary of Contents for Intesis DALI

Reviews:

Related manuals for Intesis DALI

Brands by name

Popular brands

HMS Networks Intesis DALI, User Manual

Search results

Summary of Contents for Intesis DALI

Reviews:

Related manuals for Intesis DALI

Brands by name

Popular brands