HMS Networks Intesis DALI User Manual Download Page 23 | Manualshive

Page: 23 / 34

background image

Intesis

TM

KNX

– DALI

User Manual r1.1 EN

© HMS Industrial Networks S.L.U - All rights reserved

This information is subject to change without notice

URL

http

s

://www.intesis.com

23 / 34

4.2.5 Sending the configuration to Intesis

When the configuration is finished, follow the steps to program the gateway.

1.- Click on

Save

button to save the project to the project folder on your hard disk (more information in

Intesis MAPS User Manual).

2.- You will be prompted to generate the configuration file to be sent to the gateway.

a.- If

Yes

is selected, the file containing the configuration for the gateway will be generated and

saved also into the project folder.

b.- If

NO

is selected, remember that the binary file with the project needs to be generated before

the Intesis starts to work as expected.

3.- Press the

Send File

button to send the binary file to the Intesis device. The process of file transmission

can be monitored in the Intesis Communication Console window. Intesis will reboot automatically once the
new configuration is loaded.

Figure 4.4

Intesis MAPS Receive/Send tab

After any configuration change, do not forget to send the configuration file to the Intesis using the
button

“Send”.

4.2.6 Diagnostic

To help integrators in the commissioning tasks and troubleshooting, the Configuration Tool offers some specific
tools and viewers.

In order to start using the diagnostic tools, the connection with the Gateway must be stablished.

The Diagnostic section is composed by two main parts: Tools and Viewers.

•

Tools

Use the tools section to check the current hardware status of the box, log communications into
compressed files to be sent to the support, change the Diagnostic panels’ view or send commands
to the gateway.

•

Viewers

In order to check the current status, viewer for the Internal and External protocols are available. It
is also available a generic Console viewer for general information about communications and the
gateway status. Finally, a Signals Viewer to simulate the BMS behavior or to check the current
values in the system.

«
...
21
22
23
24
25
...
»

Summary of Contents for Intesis DALI



































Reviews:

No comments

Related manuals for Intesis DALI

Brand: idiag Pages: 10

Brand: Bandit Pages: 136

Versaflo S Series

Brand: 3M Pages: 11

DBI Sala EXOFIT

Brand: 3M Pages: 32

Brand: 3M Pages: 8

Brand: Accurate Bio-Medical Technology Pages: 35

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Eagle Eye Pages: 21

Brand: Labomed Pages: 67

Brand: IFM Pages: 175

Brand: IFM Pages: 5

Brand: Major tech Pages: 12

Brand: Ocean Sonics Pages: 45

Brand: Zennio Pages: 3

Brand: Lalizas Pages: 12

BOBCAT 130 Series

Brand: Balcrank Pages: 12

Tacx Boost Bundle

Brand: Garmin Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands