HMS Networks Intesis DALI User Manual Download Page 19 | Manualshive

Page: 19 / 34

background image

Intesis

TM

KNX

– DALI

User Manual r1.1 EN

© HMS Industrial Networks S.L.U - All rights reserved

This information is subject to change without notice

URL

http

s

://www.intesis.com

19 / 34

3

Connections

Find below information regarding the Intesis connections available.

Power Supply
Must use NEC Class 2 or Limited Power Source (LPS) and SELV

rated

power supply.

If using DC power supply:
Respect polarity applied of terminals (+) and (-). Be sure the voltage
applied  is  within  the  range  admitted  (check  table  below).  The  power
supply  can  be  connected  to  earth  but  only  through  the  negative
terminal, never through the positive terminal.

Ethernet
Connect the cable coming from the IP network to the connector ETH
of  the  gateway.  Use  an  Ethernet  CAT5  cable.  If  communicating
through the LAN of the building, contact the network administrator and
make sure traffic on the port used is allowed through all the LAN path
(check the  gateway  user  manual for more  information).  Default IP is
192.168.100.246. DHCP is enabled by default.

PortA / KNX
Connect the KNX TP1 bus to connectors A3 (+) and A4 (-

) of gateway’s PortA. Respect the polarity.

PortB / DALI
Connect the DALI bus to connectors A4 (+), A3 (-

) of gateway’s PortA. Intesis provides 16VDC (+/-2%) DALI voltage

to the bus.

Console Port
Connect  a  mini-type  B  USB  cable  from  your  computer  to  the  gateway  to  allow  communication  between  the
Configuration  Software  and  the  gateway.  Remember  that  Ethernet  connection  is  also  allowed.  Check  the  user
manual for more information.

USB
Connect a USB storage device (not a HDD) if required. Check the user manual for more information.

Ensure proper space for all connectors when mounted (see section 6).

«
...
17
18
19
20
21
...
»

Summary of Contents for Intesis DALI



































Reviews:

No comments

Related manuals for Intesis DALI

Brand: DARKSTAR TECHNOLOGIES Pages: 4

Brand: TDW Pages: 2

Brand: Taurus Pages: 25

Brand: Vancare Pages: 3

Brand: Paitec Pages: 14

Brand: Tacx Pages: 2

Brand: C.E. Nierhoff & Co Pages: 7

Brand: Panasonic Pages: 30

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Brand: UNIA Pages: 62

Brand: RASHA PROFESSIONAL Pages: 11

Brand: MADRIX Pages: 24

Brand: MADRIX Pages: 28

Brand: Hammer Strength Pages: 18

Brand: Laser Pages: 2

Brand: Lars Thrane Pages: 50

Brand: Rain-Flo Irrigation Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands