HMI TRU-FIT Installation Instructions Manual Download Page 2

INSTALLATION INSTRUCTIONS

TRU-FIT 

DOOR & PANEL

GENERAL INFO:

• Please take a few minutes and thoroughly read the instruc-

tions before you start the installation.

• YOU WILL NEED TWO PEOPLE to install this unit

• If, at any point in the installation, you have questions, please 

contact the dealer through whom you purchased this enclo-

sure.

• FAILURE TO FOLLOW THE INSTRUCTIONS COULD 

RESULT IN SERIOUS INJURY, DAMAGE OR DEATH.  Not to 

scare you, but you need to take this seriously.

BEFORE YOU START YOUR INSTALLATION:

• Purchaser is responsible for observing all local plumbing and 

building codes.  Please consult your local building codes and 

compliance standards before installation to ensure conformity.

• We recommend that this enclosure be installed into secure 

wall studs on the door hinge side.  However, it should work 

fine if installed into a solid substrate (such as sheet rock board 

or green board) with the appropriate wall anchors.  A fiber

-

glass unit with nothing behind it is not suitable for mounting a 

TRU-FIT enclosure.

• Make sure your enclosure is the proper size for your opening.

• This enclosure is designed to handle minor out-of-plumb wall 

conditions and mildly uneven sill conditions.  If either of your 

walls are more than 1/2” out-of-plumb, this unit is not suitable 

for your conditions.

• If the sill is not level, there could be some variances in the 

spacing between sill and door.  It will be very IMPORTANT 

that you note these outages precisely and adjust the spacing of 

the glass off the sill accordingly so that the glass CANNOT hit 

the sill while in operation.

• Make sure you have all the proper tools.  The installer is re-

sponsible for selecting the appropriate drill bits for the installa-

tion surface conditions.

• If you are installing on freshly laid tile, allow enough time 

for the tile cement and grout to fully dry before installing the 

shower enclosure.

DISCLAIMERS:

• HMI Shower Enclosures is in no way responsible for any 

damage or bodily injury caused by an improper installation.  

Failure to follow these instructions, guidelines and warnings will 

void your warranty, and possibly cause anything form minor 

water damage to serious injury or death.

• These units have been tested under extreme usage condi-

tions and have not failed WHEN PROPERLY INSTALLED.

WHEN YOU START YOUR INSTALLATION:

• Carefully remove all the enclosure parts and components 

from the packaging and keep the packaging until the installa-

tion  is complete.  Inventory all the parts and inspect them for 

damage.  If any of the parts are damaged, please contact your 

local distributor.

AFTER INSTALLATION:

• For the first 72 hours after installation, do not operate the 

door or use the shower.  This will allow time for the silicone to 

cure properly.

• Save this manual for future references.

ITEMS LISTED AS OPTIONAL:

• The two screws for the outside of the unit to secure the 

hinge jamb to the wall jamb are HIGHLY RECOMMENDED to 

reduce movement and provide a truly stable door.

• Three different polycarbonates are provided to help prevent 

water from escaping the shower.  It is up to the installer/owner 

to determine if these are necessary.

CARE AND MAINTENANCE:

• Do not use harsh cleaners on your enclosure, as these can 

scratch or otherwise damage your enclosure.

• The shower enclosure can remain beautiful for years with the 

proper care.  Some items, such as polycarbonates, may need 

to be replaced over time when they show signs of wear, are 

yellowing, or are not as functional in holding back water.

• Water conditions vary, and my necessitate extra cleaning of 

your enclosure.

• We recommend that you wipe down your shower enclosure 

with a cloth or squeegee after each use.

TROUBLESHOOTING:

• For troubleshooting various installation issues, see at the end 

of these instructions.

IMPORTANT

CAUTION

The TRU-FIT Shower Enclosure is made of tempered glass.  While tempered glass is strong, it 

on edge is hit too hard or something else happens it can break.  Tempered glass is designed to 

shatter into small pieces, like automobile windows, but they can still be dangerous.  Take care 

when handling the glass.

V5_21_26

Summary of Contents for TRU-FIT














Reviews: