manualshive.com logo in svg

HMI TRU-FIT, Installation Instructions Manual, Page: 13 / 13

Share
Download
HMI TRU-FIT Installation Instructions Manual Download Page 13

INSTALLATION INSTRUCTIONS

TRU-FIT 

DOOR & PANEL

INSTALLATION:

If, while preparing to attach the Hinge Jamb (B) to the Wall 

Jamb (A), you are unable to get a consistent 1/8” gap between 

the Door Glass (O) and Panel Glass (P) without revealing the 

groove lines on the Wall Jamb (A), either your walls may be 

seriously out of plumb or your selected unit might not be the 

right size for your conditions.  Double check your wall condi-

tions and measurements.

OPERATION:

If you have not installed the #8 x 3/4” Set Screws (L) on the 

outside of the enclosure securing the Hinge Jamb (B) to the 

Wall Jamb (A), and you are noticing movement of the Hinge 

Jamb (B) during normal operation, we strongly suggest you go 

to Step 24 and install the Set Screws (L) on the outside of the 

enclosure.

TROUBLESHOOTING

To make a claim under the provisions of this warranty, please 

contact your local HMI Shower Enclosure dealer.  They 

should be able to solve any problem you might have.

If your dealer cannot solve your problem, they will contact 

your local HMI Shower Enclosure distribution center.

If you are unable to obtain warranty service through your 

local HMI Shower Enclosure distribution center, you can 

contact us at:

HMI 

4795 Shepherdsville Road

Louisville, KY 40218 USA

email: [email protected]

Please include all relevant information regarding your claim:

• The model which was installed.

• The name and address of the installer..

• The installation address.

• A complete description of the problem.

• A photocopy of your invoice/receipts for the product 

installed.

Under no circumstances should HMI Shower Enclosures 

products be returned to your dealer, distributor, or the HMI 

Shower Enclosures without a written Return Merchandise 

Authorization (RMA).

WARRANTY  CLAIMS

V5_21_26

Summary of Contents for TRU-FIT














Reviews:

No comments