Hitachi ZX200-5G Workshop Manual Download Page 454 | Manualshive

Page: 454 / 502

background image

9

8

4

6

ST 1955

7

3

Group 5 Upper and Lower Rollers

SECTION 4 UNDERCARRIAGE

W4-5-3-2

Disassembly of Lower Roller

d

CAUTION: Lower roller weight: 35 kg (78 lb)

1. Remove plug (1) from the end of collar (2). Drain oil

from roller (7).

l

: 6 mm

d

CAUTION: Metal fragments may fly off when

a hammer is used. Wear necessary protection,
such as goggles, helmets, etc. in order to prevent
personal injury.

2. Put the matching marks on collar (2) and axle (8).

Remove pin (3) from collar (2) by using a round bar
and a hammer. Remove axle (8) from the side of
roller (7), where pin (3) has been removed, by using
a press. At this time, pin (3) and collar (9) on the
opposite side are removed with axle (8) together.

f

NOTE: Diameter of round bar: 14 mm (0.55 in)

IMPORTANT: Handle floating seal (5) with care.

(Refer to W4-5-4.)

3. Remove floating seals (5) (2 used) from both sides of

roller (7) and collars (2, 9).

4. Remove pin (3) from the axle (8) assembly. Remove

axle (8) from collar (2) by using a press.

5. Remove O-rings (4) (2 used) from axle (8).

d

CAUTION: Roller (7) weight: 21 kg (47 lb)

IMPORTANT: Do not remove bushing (6) unless

necessary.

6. Remove bushing (6) by using the special tool (ST

1955) and a press.

5

5

9

7

5

2

8

W105-03-06-026

W178-02-11-268

W178-02-11-269

«
...
452
453
454
455
456
...
»

Summary of Contents for ZX200-5G























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZX200-5G

Brand: Komatsu Pages: 516

Brand: Gradall Pages: 164

Brand: Gradall Pages: 172

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands