Hitachi NR 65AK Service Manual Download | Manualshive

Page: 40 / 47

background image

--- 36 ---

11. INSPECTION AND CONFIRMATION AFTER REASSEMBLY

Check that Plunger (A) [47] moves smoothly.

Check that there is no air leakage from each part.

While driving nails with an air pressure of 4.5 kgf/cm

2

(63 psi), check that there is no misfiring and bending of

nails.

Recheck the tightening torque of each screw.

Check that Pushing Lever (A) [30] slides smoothly.

Check that the machine will not operate only by pulling the Trigger [52]. Also check that the machine will not

operate only by depressing Pushing Lever (A) [30].

«
...
38
39
40
41
42
...
»

Summary of Contents for NR 65AK
















































Reviews:

No comments

Related manuals for NR 65AK

Brand: Black & Decker Pages: 12

Brand: Black & Decker Pages: 18

Brand: Alpha tools Pages: 56

TrimMaster IM250A-Li

Brand: Paslode Pages: 3

Brand: Paslode Pages: 3

Brand: Paslode Pages: 12

Brand: Campbell Hausfeld Pages: 32

Brand: KMR Pages: 4

Brand: Simpson Pages: 20

Brand: Parkside Pages: 28

Brand: Campbell Hausfeld Pages: 32

Brand: Paslode Pages: 20

Brand: Paslode Pages: 12

Brand: Senco Pages: 12

Brand: Porter-Cable Pages: 15

Brand: Powermate Pages: 12

Brand: Powermate Pages: 40

PORTAPRO GG-100

Brand: Master Appliance Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands