Hitachi NE-S1 series Basic Manual Download Page 5

Page: 5 / 16

2. Name of each portion (removed front cover)

Name

Description

①

Connector for dedicated operator

for NES1-OP

Dedicated operator for NE-S1 (NES1-OP) can be connected on this connector.

②

RUN/STOP/RESET key

Push key for run, stop and reset operation.

③

Intelligent relay terminal

Output terminal for intelligent relay (1 from c contact).

④

Main terminal

For connecting power supply, motor output and DC reactor.

⑤

Switch for termination resistor

Switch for integrated termination resistor (100

) for RS485.Integrated resistor of 100

connected when switched ON.

⑥

Switch for RS485/OPE

Changeover switch for RS422/RS485 communication setting.

⑦

RS422/RS485 port

Connector for RS485 external operator or PC software (RJ45 jack)

⑧

Switch for O/OI (analog input)

changeover

Voltage input (O) or current input (OI) can be selected using this switch.

⑨

Logic terminal A,B

Terminal for connecting input/output signals (digital/analog) for the inverter control.

⑩

Charge lamp

Turns ON when the internal DC bus voltage is 45V or more.

In case of wiring, maintenance or else, please be sure to check that this lamp is turned OFF

after waiting 10 minutes of power OFF.

Note

１

) Refer to page 13 for the description of the display and key operation.

Note 2) Position of

⑩

charge lamp depends on the model. Refer to page 11 for the details.

Note 3) Pay attention when operating by PC via

⑦

RS422/RS485 port, as the operation can also be done from the panel of the inverter.

Note 4) Be sure to turn power OFF when connecting or disconnecting the operator such as OPE-SRmini,OPE-S,WOP to the

⑦

RS422/RS485

port.

3. Cautions for installation

①

Caution during transportation

Please pay attention when carrying the product as it is covered by a plastic case.

Especially, do not put pressure onto the front cover and terminal cover. Otherwise there is a risk of damaging the product.

Please do not use products that are damaged, and/or lacking components.

⑥

Switch for RS485/OPE SW5

⑤

Switch for termination resistor SW4

⑦

RS422/RS485 port

②

RUN/STOP/RESET keys

④

Main terminal

⑨

Logic terminal A

P8 to 9

⑧

Switch for O/OI (analog input)

changeover SW6

⑨

Logic terminal B

③

Intelligent relay terminal

⑩

Charge indicator lamp

①

Connector for dedicated

operator for NES1-OP

P8 to 9

OFF

(Default)

RS485

OPE

(Default)

→

Voltage O

(Default)

Current OI

P8 to 9

Summary of Contents for NE-S1 series

















Search results

Summary of Contents for NE-S1 series

Reviews:

Related manuals for NE-S1 series

Brands by name

Popular brands

Hitachi NE-S1 series, Basic Manual

Search results

Summary of Contents for NE-S1 series

Reviews:

Related manuals for NE-S1 series

Brands by name

Popular brands