Hitachi ED-X8255 User Manual Download

Page: 23 / 108

Operating

Operating the computer screen

CAUTION

►Mistaken use of the mouse/keyboard control could damage

your equipment.

• While using this function, please connect only with a computer.

• Before connecting, read the manuals of the computer you will connect.

NOTE

• It may not be possible to control notebook PC, and other computers with

built-in pointing device (e.g. track ball), using this remote control. In this case, before

connecting go into BIOS (system setup) and select external mouse, and disable the

pointing device. In addition, the mouse may not function if the computer does not have

the needed utility program. See your computer’s hardware manual for details.

• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be

possible to use the remote control, depending on the computer’s conﬁgurations and

mouse drivers.

• The USB control can be used only for the functions listed below. You cannot do things

like press two buttons at once (for instance, pressing two buttons at the same time to

move the mouse pointer diagonally).

• This function is not available while the lamp is warming up (the POWER indicator

ﬂashes green), and while adjusting the volume and display, correcting for trapezoidal

distortion, zooming in on the screen, using the BLANK function, or displaying the menu

screen.

USB

mouse and keyboard control

Connect the projector’s USB port to the computer via the mouse cable.

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RGB

FREEZE

OFF

MAGNIFY

ASPECT

AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

Available function

Remote control operation

Move pointer

Use ▲, ▼, ◄, ► buttons

Left click with mouse

Press ENTER button

Right click with mouse

Press RESET button

Press keyboard’s HOME key

Press HOME button

Press keyboard’s END key

Press END button

Press keyboard’s PAGE UP key

Press PAGE UP button

Press keyboard’s PAGE DOWN key

Press PAGE DOWN button

Press keyboard’s ESC key

Press ESC button

Summary of Contents for ED-X8255













































































































Search results

Summary of Contents for ED-X8255

Reviews:

Related manuals for ED-X8255

Brands by name

Popular brands

Hitachi ED-X8255, User Manual

Search results

Summary of Contents for ED-X8255

Reviews:

Related manuals for ED-X8255

Brands by name

Popular brands