Hitachi ED-X8255 User Manual Download

Page: 18 / 108

Operating

Adjusting the volume

Press the VOLUME button on the remote control.

A dialog will appear on the screen to aid you in adjusting the volume.

Use the cursor buttons ▲/▼ to adjust the volume.
To close the dialog and complete the operation, press the

VOLUME button again. Even if you don’t do anything, the

dialog will automatically disappear after a few seconds.

Temporarily muting the sound

Press the MUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted the sound.

To restore the sound, press the MUTE or VOLUME button.

Even if you don’t do anything, the dialog will automatically

disappear after a few seconds.

Selecting an input signal

Press the INPUT button on the projector.

Each time you press the button, the projector switches its

input port as below.
RGB IN1



RGB IN2

VIDEO



S-VIDEO



COMPONENT VIDEO

● When the RGB IN2/RGB OUT port functions as an RGB out

port (the RGB IN OUT switch is pushed in), RGB IN2 cannot

be selected. In that case “RGB2/RGB OUT



RGB OUT” message will be

displayed.

Press the RGB button on the remote control to select an

input port for the RGB signal.

Each time you press the button, the projector switches its RGB

input port as below.
RGB IN1



RGB IN2

● If the RGB button is pushed (when switching from VIDEO to RGB signals)

when TURN ON is selected for the AUTO SEARCH item in the OPTION menu

the projector will check the RGB IN1 port ﬁrst. If no input is detected at the port,

the projector will check the RGB IN2 port.

● When the RGB IN2/RGB OUT port functions as an RGB out port (the RGB IN

OUT switch is pushed in), RGB IN2 cannot be selected. In that case “RGB2/

RGB OUT



RGB OUT” message will be displayed.

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RGB

FREEZE

OFF

MAGNIFY

ASPECT

AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RGB

FREEZE

OFF

MAGNIFY

ASPECT

AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RGB

FREEZE

OFF

MAGNIFY

ASPECT

AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

Summary of Contents for ED-X8255













































































































Search results

Summary of Contents for ED-X8255

Reviews:

Related manuals for ED-X8255

Brands by name

Popular brands

Hitachi ED-X8255, User Manual

Search results

Summary of Contents for ED-X8255

Reviews:

Related manuals for ED-X8255

Brands by name

Popular brands