Hitachi ED-X8255 User Manual Download

Page: 21 / 108

Using the magnify feature

Press the ON button of MAGNIFY on the remote control.

The “MAGNIFY” indication will appear on the screen

(although the indication will disappear in several seconds with

no operation), and the projector will enter the MAGNIFY mode.

Use the cursor buttons ▲/▼ to adjust the zoom level.
To move the zoom area, press the POSITION button in the MAGNIFY mode,

then use the cursor buttons ▲/▼/◄/► to move the area. And to ﬁnalize the

zoom area, press the POSITION button again.
To exit the MAGNIFY mode and restore the screen to normal, press the OFF

button of MAGNIFY on the remote control.

● The projector automatically exits the MAGNIFY mode when the input signal is

changed, or when the display condition is changed.

● Although in the MAGNIFY mode, the keystone distortion condition may vary, it

will be restored when the projector exits the MAGNIFY mode.

Operating

Correcting the keystone distortions

Press the KEYSTONE button on the remote control. A

dialog will appear on the screen to aid you in correcting the

distortion.

Use the cursor buttons ▲/▼ to correct the distortion.

To close the dialog and complete this operation, press the

KEYSTONE button again. Even if you don’t do anything, the

dialog will automatically disappear after a few seconds.

● The adjustable range for correction will vary among inputs. For some input, this

function may not work well.

● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the

SETUP menu, if the projector screen is inclined or angled downward, this

function may not work correctly.

● When the zoom adjustment is set to the TELE (telephoto focus), this correction

may be excessive. This function should be used when the zoom adjustment is

set to the WIDE (wide-angle focus) whenever possible.

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RGB

FREEZE

OFF

MAGNIFY

ASPECT

AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RGB

FREEZE

OFF

MAGNIFY

ASPECT

AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

Summary of Contents for ED-X8255













































































































Search results

Summary of Contents for ED-X8255

Reviews:

Related manuals for ED-X8255

Brands by name

Popular brands

Hitachi ED-X8255, User Manual

Search results

Summary of Contents for ED-X8255

Reviews:

Related manuals for ED-X8255

Brands by name

Popular brands