Hitachi ED-X8255 User Manual Download

Page: 17 / 108

Power on/off

WARNING

►When the power is on, a strong light is emitted. Do not look into

the lens of projector. Also do not peep at the inside of projector through a hole.

NOTE

• Turn the power on/off in right order. Please power on the projector prior

to the connected devices. Power off the projector later than the connected devices.

Turning on the power

Make sure that the power cord is ﬁrmly and

correctly connected to the projector and the

outlet.

Remove the lens cover, and set the power

switch to the ON position.

The power indicator will light up in steady orange.

Then wait several seconds because the buttons

may not function for these several seconds.

Press the STANDBY/ON button on the projector or the remote control.

The projector lamp will light up and the POWER

indicator will begin blinking in green. When the power is

completely on, the indicator will stop blinking and light in

green.

To display the picture, select an input signal according to

the section "Selecting an input signal"

(



)

Turning off the power

This product is able to turn off the main power during the cooling. However, please

pay special attention to below two points when you do:
(1) Please do not turn the projector on again for at least 1 minute in this case.

Neglect could shorten the lifetime of the lamp.

(2) During use or immediately after use, do not touch around the lamp and vents

of the projector

(





)

It could cause a burn.

Press the STANDBY/ON button on the projector or the remote control.

The message "Power off?" will appear on the screen for approximately 5

seconds.

Press the STANDBY/ON button on the projector or the

remote control again while the message appears.

The projector lamp will go off, and the POWER indicator will

begin blinking in orange.
Then the POWER indicator will stop blinking and light in

steady orange when the lamp cooling is complete.

Make sure that the power indicator lights in steady orange,

and set the power switch to the OFF position. The POWER

indicator will go off. Attach the lens cover.

POWER

(Steady orange)

POWER

(Blinking in green)

POWER

(Steady green)

HOME

PAGE UP

PAGE DOWN

END

VIDEO

RGB

FREEZE

OFF

MAGNIFY

ASPECT

AUTO

BLANK

MUTE

VOLUME

KEYSTONE

POSITION

ESC

ENTER

RESET

STANDBY/ON

button

POWER

indicator

Power off?

POWER

(Blinking in orange)

POWER

(Steady orange)

Summary of Contents for ED-X8255













































































































Search results

Summary of Contents for ED-X8255

Reviews:

Related manuals for ED-X8255

Brands by name

Popular brands

Hitachi ED-X8255, User Manual

Search results

Summary of Contents for ED-X8255

Reviews:

Related manuals for ED-X8255

Brands by name

Popular brands