Hitachi CP-WU8600 User Manual Download Page 62

Page: 62 / 129

PICTURE menu

PICTURE menu

From the PICTURE menu, items shown in the table

below can be performed.

Select an item using the ▲/▼ cursor buttons, and

press the ► cursor button or

ENTER

button to

execute the item. Then perform it according to the

following table.

Item

Description

BRIGHTNESS

Using the ◄/► buttons adjusts the brightness.

Dark

Light

CONTRAST

Using the ◄/► buttons adjusts the contrast.

Weak

Strong

COLOR

Using the ◄/► buttons adjusts the strength of whole color.

Weak

Strong

TINT

Using the ◄/► buttons adjusts the tint.

Reddish

Greenish

SHARPNESS

Using the ◄/► buttons adjusts the sharpness.

Weak

Strong

• There may be some noise and/or the screen may flicker for a

moment when an adjustment is made. This is not a malfunction.

ACTIVE IRIS

Using the ▲/▼ cursor buttons changes the active iris control mode.

PRESENTATION

THEATER

OFF

PRESENTATION : The active iris displays the best presentation

image for both bright and dark scenes.

THEATER : The active iris displays the best theater image for

both bright and dark scenes.

OFF : The active iris is always open.

• The screen may flicker when the PRESENTATION or THEATER

modes are selected. If this occurs select OFF.

(continued on next page)

Summary of Contents for CP-WU8600


































































































































Search results

Summary of Contents for CP-WU8600

Reviews:

Related manuals for CP-WU8600

Brands by name

Popular brands

Hitachi CP-WU8600, User Manual

Search results

Summary of Contents for CP-WU8600

Reviews:

Related manuals for CP-WU8600

Brands by name

Popular brands