Hitachi CP-WU8600 User Manual Download Page 121

Page: 121 / 129

121

Resetting all settings

When it is hard to correct some wrong settings, the FACTORY RESET function of

SERVICE item in OPTION menu (



) can reset all settings (except settings such

as LANGUAGE, AUTO BLANK, LAMP TIME, FILTER TIME, FILTER MESSAGE,

STANDBY MODE, COMMUNICATION, SECURITY and NETWORK)

to the factory default.

• When the interior portion has become overheated, for safety

purposes, the projector is automatically shut down, and the indicator lamps

may also be turned off. In such a case, disconnect the power cord, and wait at

least 45 minutes. After the projector has sufficiently cooled down, please make

confirmation of the attachment state of the lamp and lamp cover, and then turn

the power on again.

NOTE

For the

SECURITY

indicator, see SECURITY INDICATOR in the SECURITY

menu (



107

For the

SHADE

indicator, see the section "

Temporarily shading the screen

(



The

FILTER

indicator shows the condition of the air filter. Utilize this feature to

keep the interior of the projector in good condition.

FILTER indicator

Description

Turned

off

The air filter is clean.

No need to clean up.

Lighting In

Orange

The air filter is going to be choked.

It is recommended to clean it. In addition, please see the

section "There is a possibility that the interior portion has

become heated" (



119

Lighting In

Red

The air filter is choked.

It is required to turn the power off and clean the air filter

immediately. In addition, please see the section "There is a

possibility that the interior portion has become heated" (



119

Regarding the indicator lamps

Regarding the indicator lamps (continued)

• The

FILTER

indicator might light up in orange or red when something

blocks the intake vents even though the air filter is clean.

• The

FILTER

indicator might light up differently from other indicators or display

messages related to cleaning the air filter. Follow the prompt that is displayed

earlier.

NOTE

Summary of Contents for CP-WU8600


































































































































Search results

Summary of Contents for CP-WU8600

Reviews:

Related manuals for CP-WU8600

Brands by name

Popular brands

Hitachi CP-WU8600, User Manual

Search results

Summary of Contents for CP-WU8600

Reviews:

Related manuals for CP-WU8600

Brands by name

Popular brands