Hitachi C 10FCE Technical Data And Service Manual Download Page 50

Page: 50 / 62

* ALTERNATIVE PARTS

--- 3 ---

ITEM

NO.

CODE NO.

DESCRIPTION

REMARKS

NO.

USED

PARTS

4 -- 04

C 10FCH

323-141

SPRING (B)

323-137

LASER HOLDER (A)

323-138

LASER HOLDER (B)

949-900

ROLL PIN D3X14 (10 PCS.)

323-142

SPRING (C)

962-782

HEX. SOCKET SET SCREW M5X6

949-531

SPLIT PIN D2X12 (10 PCS.)

323-144

SPECIAL BOLT M5

975-144

CABLE TIE

307-956

SEAL LOCK HEX. SOCKET SET SCREW M6X10

323-135

LASER MODULE

323-143

WASHER

323-140

SPRING (A)

323-136

LASER COVER

323-139

LASER BASE ASS’Y

INCLUD. 16

CAUTION LABEL (A)

322-927

LASER HOLDER ASS’Y

INCLUD. 1-9, 11-15

322-889

SLEEVE

322-890

SPRING

322-965

LINER (D)

302-518

STOPPER PIN ASS’Y

INCLUD. 22

984-528

O-RING (P-6)

997-314

MACHINE SCREW (W/WASHERS) M6X10

322-935

CLAMP LEVER

322-936

BOLT (LEFT HAND) M10

318-934

SPECIAL WASHER

322-933

SHAFT (D)

322-934

WASHER M16

322-888

SHAFT (C)

322-932

HINGE

322-937

LINER (B)

322-963

DUST GUIDE HOLDER

949-215

MACHINE SCREW M4X8 (10 PCS.)

949-652

HEX. SOCKET HD. BOLT M6X25 (10 PCS.)

322-891

DUST GUIDE ASS’Y

INCLUD. 32, 33, 37

990-541

MACHINE SCREW (W/WASHERS) M5X16

322-892

SCALE (B)

303-409

NYLOCK BOLT M8X25

322-930

TABLE INSERT (B)

322-929

TABLE INSERT (A)

949-217

MACHINE SCREW M4X12 (10 PCS.)

949-429

BOLT WASHER M4 (10 PCS.)

680-418

NYLON NUT M12

322-893

INDICATOR (B)

304-043

MACHINE SCREW (W/WASHERS) M4X10 (BLACK)

975-348

NYLON NUT M8

318-929

WASHER (F)

304-043

MACHINE SCREW (W/WASHERS) M4X10 (BLACK)

322-904

INDICATOR (A)

322-897

TURN TABLE

322-898

SIDE HANDLE

Summary of Contents for C 10FCE































































Search results

Summary of Contents for C 10FCE

Reviews:

Related manuals for C 10FCE

Brands by name

Popular brands

Hitachi C 10FCE, Technical Data And Service Manual

Search results

Summary of Contents for C 10FCE

Reviews:

Related manuals for C 10FCE

Brands by name

Popular brands