![background image](http://html.mh-extra.com/html/hilti/dd-af-ca-l/dd-af-ca-l_original-operating-instructions_2134971026.webp)
20
English
2289378
*2289378*
3. Turn the auto-feed unit until the square shaft engages in the square-shaft adapter on the carriage.
4. Hold the auto-feed unit and disengage the carriage lock.
5. Position the auto-feed unit at one of the 5 keyed mounting positions.
▶
The auto-feed unit engages correctly at the keyed position.
▶
The
EMERGENCY STOP
switch is freely accessible.
▶
The auto-feed unit does not obstruct the planned drilling operation.
6. Tighten the securing screw by hand.
7. Connect the cooling water connector of the auto-feed unit to the water connection of the diamond core
drilling machine.
8. Connect the electric supply cord and the water supply hose.
▶
The water valve switches with an audible click.
9. Check that the auto-feed unit and the cooling water supply are correctly installed and connected.
5.2
Pairing auto-feed unit and diamond core drilling machine
5.2.1 Establishing a new Bluetooth connection (pairing)
Before you can use the auto-feed unit with a diamond core drilling machine as a drilling system, you have
to pair the two system products via Bluetooth. This pairing remains saved as a successful pairing operation
until you pair another auto-feed unit to the diamond core drilling machine, overwriting the existing pairing.
Pair the auto-feed unit only to a diamond core drilling machine recommended by
Hilti
. The supply
voltage must match the ratings stated on the rating plate of the diamond core drilling machine.
1. Install the auto-feed unit on the carriage of the drill stand. → page 19
2. Establish the electricity supply to the drilling system.
3. Simultaneously press the
and
buttons on the diamond core drilling machine.
4. Check that the
EMERGENCY STOP
switch is in full working order. → page 18
▶
The auto-feed unit pairs with the diamond core drilling machine.
▶
A symbol appears in the status bar of the display.
Other paired system products (e.g. DD WMS 100) can also be shown in the status bar.
5. The drilling system changes to the "
Position CUT-ASSIST
" mode.
▶
The corresponding status indicator appears on the display.
5.2.2 Re-establishing an existing Bluetooth connection
When power is switched on, the auto-feed unit automatically attempts to re-establish the Bluetooth to the
diamond core drilling machine to which it is currently paired.
1. Establish the electricity supply to the drilling system.
2. Check that the
EMERGENCY STOP
switch is in full working order. → page 18
▶
The auto-feed unit establishes a connection to the diamond core drilling machine.
▶
A symbol appears in the status bar of the display.
Other paired system products (e.g. DD WMS 100) can also be shown in the status bar.
3. The drilling system changes to the "
Position CUT-ASSIST
" mode.
▶
The corresponding status indicator appears on the display.
6
Types of work
WARNING
Damaged power cords are a safety hazard!
If the supply cord or extension cord is damaged while work
is in progress, immediately disconnect the device and the cord from the electricity supply. Do not touch the
damaged part of the cord.
▶
Regularly check all supply cords. Replace defective extension cords. Have damaged power cords
replaced by a qualified specialist.
Summary of Contents for DD AF-CA L
