hilscher 1912.112 User Manual Download Page 35

Page: 35 / 154

Configuration

35/154

8.3.5.1

Channel Selection

Select

Master

in the left column of the netFIELD Wireless Web Server.

The

Channel Selection

tab appears.

Figure 6: Channel selection tab

Use the Channel Selection tab to select the WLAN channels required for
operation.

Parameter

Description

Value, Value range

WLAN Channel 01 …
WLAN Channel 13

List of WLAN channels 01 to 13 on the 2.4 GHz frequency
band.

The radio symbols indicate whether a channel is activated
and if fully or partly.

Use mouse over to indicate the help text.

“checked”, “unchecked” (default)

Table 20: IO-Link Wireless Master settings - Channel selection

Select the operating channels required for device operation.

Click

Apply

The selected WLAN channels are configured.

Summary of Contents for 1912.112



























































































































































Search results

Summary of Contents for 1912.112

Reviews:

Related manuals for 1912.112

Brands by name

Popular brands

hilscher 1912.112, User Manual

Search results

Summary of Contents for 1912.112

Reviews:

Related manuals for 1912.112

Brands by name

Popular brands