background image

DS-K1201 Fingerprint Card Reader 

iii 

Regulatory Information 
FCC Information 
Please  take  attention  that  changes  or modification  not  expressly  approved  by  the 
party  responsible  for  compliance  could  void  the  user’s  authority  to  operate  the 
equipment. 
FCC  compliance:  This  equipment  has  been  tested  and  found  to  comply  with  the 
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits 
are  designed  to  provide  reasonable  protection  against  harmful  interference  in  a 
residential  installation.  This  equipment  generates,  uses  and  can  radiate  radio 
frequency energy and, if not installed and used in accordance with the instructions, 
may  cause  harmful  interference  to  radio  communications.  However,  there  is  no 
guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures: 
—Reorient or relocate the receiving antenna. 
—Increase the separation between the equipment and receiver. 
—Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which 
the receiver is connected. 
—Consult the dealer or an experienced radio/TV technician for help. 
FCC Conditions 
This  device  complies  with  part  15  of  the  FCC  Rules.  Operation  is  subject  to  the 
following two conditions: 
1. This device may not cause harmful interference. 
2.  This  device  must  accept  any  interference  received,  including  interference  that 
may cause undesired operation. 
EU Conformity Statement 

This  product  and  -  if  applicable  -  the  supplied  accessories  too  are 
marked  with  "CE"  and  comply  therefore  with  the  applicable 
harmonized  European  standards  listed  under  the  EMC  Directive 
2014/30/EU, the RoHS Directive 2011/65/EU.   

2012/19/EU  (WEEE  directive):  Products  marked  with  this  symbol 
cannot be disposed of as unsorted municipal waste in the European 
Union.  For  proper  recycling,  return  this  product  to  your  local 
supplier  upon  the  purchase  of  equivalent  new  equipment,  or 
dispose  of  it  at  designated  collection  points.  For  more  information 

see

www.recyclethis.info

 

2006/66/EC  (battery  directive):  This  product  contains  a  battery  that  cannot  be 
disposed  of  as  unsorted  municipal  waste  in  the  European  Union.  See  the  product 

Summary of Contents for DS-K1201A Series
















Reviews: