HIKVISION DS-7204HTI-K1 User Manual Download Page 44

Page: 44 / 188

DS-720xHTI-Kx DVR User Manual

UM DS-720xHTI-Kx 012918NA

(Optional) Check the

Enable Omnicast Control

checkbox to enable the PTZ control of the selected

camera via Omnicast VMS of Genetec.

4.2 Setting PTZ Presets, Patrols, and Patterns

Before You Start

Make sure that the presets, patrols, and patterns are supported by the PTZ protocols.

4.2.1 Customizing Presets

Purpose

To set the preset location you want the PTZ camera to point to when an event occurs.

Go to

Menu > Cameras Setup > PTZ

Figure 4-4

PTZ Settings

Use the directional button to wheel the camera to the location where you want to set preset; and the
zoom and focus operations can be recorded in the preset as well.

Enter the preset No. (1~255) in the preset text field, and click

Set

to link the location to the preset.

Repeat steps from 2 to 3 to save more presets.

You can click

Clear

to clear the location information of the preset, or click

Clear All

to clear the location

information of all the presets.

Summary of Contents for DS-7204HTI-K1





























































































































































































Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands

HIKVISION DS-7204HTI-K1, User Manual

Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands