HIKVISION DS-7204HTI-K1 User Manual Download Page 101

Page: 101 / 188

DS-720xHTI-Kx DVR User Manual

UM DS-720xHTI-Kx 012918NA

100

Figure 8-5

Motion Detection

Select the connected PIR camera.

Check Enable Motion Detection.

Check

False Alarm Filter

to enable PIR motion detection. The message box pops up as below.

Figure 8-6

Note

Click

to enable PIR motion detection. Then, only when the motion detection events and PIR events

are both triggered, the motion detection alarm will be triggered.

Set detection area and sensitivity. Refer to

8.1

Setting Motion Detection

Click

Set

to set motion detection alarm response actions. See

8.1 Setting Motion Detection

Click

Apply

to save the settings.

This function is applicable only to Hikvision PIR analog cameras.

The PIR alarm does not support detection area configuration. It is full screen by default.

The PIR alarm does not support sensitivity configuration.

If you disable the false alarm filter, only when the motion detection events are triggered will the
motion detection alarm be triggered. The PIR alarm will not be considered.

Summary of Contents for DS-7204HTI-K1





























































































































































































Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands

HIKVISION DS-7204HTI-K1, User Manual

Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands