HIKVISION DS-7204HTI-K1 User Manual Download Page 133

Page: 133 / 188

DS-720xHTI-Kx DVR User Manual

UM DS-720xHTI-Kx 012918NA

132

Chapter 11 Network Settings

11.1 Configuring General Settings

Purpose

Network settings must be properly configured before you operate the DVR over a network.

Go to

Menu > System Configuration > Network > General

Figure 11-1

Network Settings Interface

On the

General Settings

interface, you can configure the following parameters: NIC Type, IPv4 Address,

IPv4 Gateway, MTU, DNS Server, and Main NIC.

The valid value of MTU is from 500 to 1500.

If the DHCP server is available, you can check the

Enable

DHCP

checkbox to automatically obtain an IP

address and other network settings from that server.

If DHCP is enabled, you can check the

Enable DNS DHCP

checkbox

or uncheck it and edit the

Preferred

DNS Server

and

Alternate DNS Server

After configuring the general settings, click

Apply

to save the settings.

Summary of Contents for DS-7204HTI-K1





























































































































































































Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands

HIKVISION DS-7204HTI-K1, User Manual

Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands