HIKVISION DS-7204HTI-K1 User Manual Download Page 17

Page: 17 / 188

DS-720xHTI-Kx DVR User Manual

UM DS-720xHTI-Kx 012918NA

Chapter 2 Getting Started

2.1 Starting Up and Shutting Down the DVR

Purpose

Proper startup and shutdown procedures are crucial to expanding the life of the DVR.

Before You Start

Check that the voltage of the external power supply matches the DVR’s requirement, and ensure that the
ground connection is working properly.

Starting up the DVR

Check that the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an
Uninterruptible Power Supply (UPS) be used in conjunction with the device.

Turn on the power switch on the rear panel, and the Power indicator LED should turn on indicating that
the unit is starting up.

After startup, the Power indicator LED remains on.

User Logout, Shutdown, and Reboot

You can log out of the system, shut down, or reboot the device upon demand.

Go to

Menu > System Maintenance

Click the

icon in the bottom left corner of the screen.

Click

Logout

Shutdown

, or

Reboot

If logged out, menu operation is invalid; enter a user name and password to unlock system.

Summary of Contents for DS-7204HTI-K1





























































































































































































Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands

HIKVISION DS-7204HTI-K1, User Manual

Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands