HIKVISION DS-7204HTI-K1 User Manual Download Page 150

Page: 150 / 188

DS-720xHTI-Kx DVR User Manual

149

After the HDD has been initialized, the HDD status will change from

Uninitialized

Normal

Initializing the HDD will erase all data on it.

HDDs that are idle for a long period of time can be put to sleep to decrease the power consumption and
extend the life of the HDDs.

Go to

Menu > System Configuration > HDD > Record Information

Figure 12-4

Enable HDD Sleeping

Check the

Enable HDD Sleeping

checkbox

(by default), and the HDDs that are idle for a long period of

time will be set to sleep.

(Optional) Uncheck the

Enable HDD Sleeping

checkbox, and the HDDs will be set to work at all times.

12.2 Managing Network HDD

Purpose

You can add the allocated NAS or IP SAN disk to the DVR and use it as a network HDD.

Go to

Menu > System Configuration > HDD > HDD Information

Figure 12-5

HDD Information Interface

Summary of Contents for DS-7204HTI-K1





























































































































































































Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands

HIKVISION DS-7204HTI-K1, User Manual

Search results

Summary of Contents for DS-7204HTI-K1

Reviews:

Related manuals for DS-7204HTI-K1

Brands by name

Popular brands