background image

Regulatory Information 
FCC Information 
Please take attention that changes or modification not 

expressly approved by the party responsible for 
compliance could void the user’s authority to operate the 
equipment. 

FCC compliance: This equipment has been tested and 
found to comply with the limits for a Class A digital 

device, pursuant to part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against 

harmful interference when the equipment is operated in 
a commercial environment. This equipment generates, 

uses, and can radiate radio frequency energy and, if not 

installed and used in accordance with the instruction 
manual, may cause harmful interference to radio 

communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in 
which case the user will be required to correct the 

interference at his own expense. 
FCC Conditions 
This device complies with part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 
1. This device may not cause harmful interference. 

2. This device must accept any interference received, 
including interference that may cause undesired 
operation. 
 
EU Conformity Statement 

This product and - if applicable - the 

supplied accessories too are marked with 
"CE" and comply therefore with the 
applicable harmonized European standards 

listed under the Low Voltage Directive 2014/35/EU, the 
EMC Directive 2014/30/EU, the RoHS Directive 
2011/65/EU. 

2012/19/EU (WEEE directive): Products 
marked with this symbol cannot be 
disposed of as unsorted municipal waste in 

the European Union. For proper recycling, 
return this product to your local supplier 
upon the purchase of equivalent new 

equipment, or dispose of it at designated collection 
points. For more information see: www.recyclethis.info. 

2006/66/EC (battery directive): This product contains a 

battery that cannot be disposed of as 
unsorted municipal waste in the European 
Union. See the product documentation for 

specific battery information. The battery is 
marked with this symbol, which may 

include lettering to indicate cadmium (Cd), lead (Pb), or 

mercury (Hg). For proper recycling, return the battery 

to your supplier or to a designated collection point. For 
more information see: www.recyclethis.info. 

 
Industry Canada ICES-003 Compliance 
This device meets the CAN ICES-3 (A)/NMB-3(A) 

standards requirements. 

 

Warning 
This is a class A product. In a domestic environment this 

product may cause radio interference in which case the 
user may be required to take adequate measures. 

 

Summary of Contents for DS-2CE71D0T-PIRL

















Reviews: