HIAB K-HiPro 285-425-4 Series Operator'S Manual Download Page 80

Page: 80 / 114

7. Ending crane operation

7.1. Operate the boom system into transport position

WARNING

• A crane with add-on equipment can differ from the operations described in this

section.

• For this reason, study the operating instructions for any add-on equipment

carefully.

DANGER

• During folding of the boom system, always

operate the crane manually from the

position indicated in the figure.

• With remote controlled cranes, stay in a

safety area while the boom system is

moving.

Operate the boom system

1. Retract the extensions completely (1).
2. Slew the crane until the crane is parallel to the vehicle

(2).

3. Lower the boom system against the vehicle (3). (Do

not extend the second boom cylinder fully).

Ending crane operation

HIAB K-HiPro 285-425 X4

Summary of Contents for K-HiPro 285-425-4 Series



















































































































Search results

Summary of Contents for K-HiPro 285-425-4 Series

Reviews:

Related manuals for K-HiPro 285-425-4 Series

Brands by name

Popular brands

HIAB K-HiPro 285-425-4 Series, Operator'S Manual

Search results

Summary of Contents for K-HiPro 285-425-4 Series

Reviews:

Related manuals for K-HiPro 285-425-4 Series

Brands by name

Popular brands