HIAB K-HiPro 285-425-4 Series Operator'S Manual Download Page 98 | Manualshive

Page: 98 / 114

background image

2. Drain the oil tank through the drain plug (1). Make

sure the system contains as little as possible.
The capacity of the tank is 40-235 litres (10.6-62

gallon). Use a container with sufficient capacity.

NOTE

Ensure the waste oil is disposed of safely and in accordance with local

environmental regulations.

3. Change at the same time:

- all filters

4. Refit the drain plug.
Filling the oil tank with hydraulic oil
The oil used for filling must be clean. Do not mix different oils.
Hydraulic oils must have been dealt with according to cleanliness requirements ISO 4406: -/16/13.
Hydraulic oil that is approved for HIAB products must comply with one of the following standards or

equivalents:
- ISO 11158 HV
- DIN 51524 part 3 HVLP
- ISO 6743/4 L-HV
Suppliers of hydraulic oil must verify that the quality and performance of the oil complies with the

above standards.
When changing from mineral oil to a non-polluting synthetic oil, or when changing to biodegradadle

oil, contact a HIAB service workshop.

Viscosity of oil

The viscosity of the oil is of great importance to achieve high efficiency of the hydraulic system.
The naming of the oil in the table below: 32, 46 or 68 tells the viscosity of that oil at 40°C (reference

temperature).

➀

Maintenance and Service

98

HIAB K-HiPro 285-425 X4

«
...
96
97
98
99
100
...
»

Summary of Contents for K-HiPro 285-425-4 Series



















































































































Reviews:

No comments

Related manuals for K-HiPro 285-425-4 Series

Brand: Makita Pages: 8

Brand: VECTECH Pages: 5

Brand: RASHA PROFESSIONAL Pages: 11

Brand: MADRIX Pages: 24

Brand: MADRIX Pages: 28

Brand: Abicor Binzel Pages: 92

Brand: Federal Signal Corporation Pages: 12

Brand: JB-Lighting Pages: 32

Brand: JBL Pages: 38

Brand: JBSYSTEMS Light Pages: 32

Brand: Dantel Pages: 22

INTEGRA ARINC e-NAV

Brand: Kannad Pages: 20

INTRA PROPHYwiz 181 P

Brand: KaVo Pages: 22

Brand: Festo Pages: 40

Brand: Neurotech Pages: 24

Brand: B&G Pages: 16

Portable Vocal Booth Pro Studio Series

Brand: EditorsKeys Pages: 2

Calculite C6P38MHA

Brand: Lightolier Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands