HIAB K-HiPro 285-425-4 Series Operator'S Manual Download Page 8

Page: 8 / 114

NOTE

HIAB shall at all times have the right to:
• install, maintain and dismantle automated remote diagnostics system or similar

sensor-based system (the “System”) in and from the Equipment; and

• access, send, receive, collect, store and use any and all information and data

gathered or created by such System including but not limited to information

concerning operation, operating environment, movement, condition, logon,

location and similar information relating to the Equipment (the “Information”).

The Customer shall not in any way remove or alter the System, nor interfere with

the use of the System or the Information. The System and the Information and all

their further developments shall at all times be and remain the exclusive property

of HIAB without granting any right or license to the customer.

1.2. Cleanliness certificate

All Hiab equipment has been tested and certified at the

factory according to the Hiab Standard C250.52 that

defines the Cleanliness Requirements for Hydraulic

Systems. This means that they fulfil the cleanliness class

20/18/14 measured by the ISO 4406 standard.
All hydraulic functions have been individually tested and

fully comply with the defined requirements.

1.3. Indications in the Operator’s Manual

What must you do and not do?

The following indications are used in the Operator’s Manual:

DANGER

Danger to life for yourself or to bystanders.
Follow the instructions carefully!

WARNING

Danger of injury to yourself or to bystanders, or danger of serious damage to the

crane or other objects.
Follow the instructions carefully.

CAUTION

Hazard for the crane or crane components. Follow the instructions carefully.

Introduction

HIAB K-HiPro 285-425 X4

Summary of Contents for K-HiPro 285-425-4 Series



















































































































Search results

Summary of Contents for K-HiPro 285-425-4 Series

Reviews:

Related manuals for K-HiPro 285-425-4 Series

Brands by name

Popular brands

HIAB K-HiPro 285-425-4 Series, Operator'S Manual

Search results

Summary of Contents for K-HiPro 285-425-4 Series

Reviews:

Related manuals for K-HiPro 285-425-4 Series

Brands by name

Popular brands