HHP Adaptus Image Kiosk TT8870 Programming Manual Download Page 68

Page: 68 / 149

5 - 26

Image Kiosk™ TT8870 Programming Guide

Linear Symbologies

EAN/JAN-13 Addenda

This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data.
Default = Off for both 2 Digit and 5 Digit Addenda.

EAN/JAN-13 Addenda Required

When Addenda Required is set to on, the imager will only read EAN/JAN-13 bar
codes that have addenda.

Default = Not Required.

EAN/JAN-13 Addenda Separator

When this feature is on, there is a space between the data from the bar code and
the data from the addenda. When turned off, there is no space.
Default = On.

Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer

UPC-A/EAN-13 with Extended Coupon Code

(page 5-21).

* 5 Digit Addenda Off

5 Digit Addenda On

* 2 Digit Addenda Off

2 Digit Addenda On

* Not Required

Required

Off

* On

Summary of Contents for Adaptus Image Kiosk TT8870






















































































































































Search results

Summary of Contents for Adaptus Image Kiosk TT8870

Reviews:

Related manuals for Adaptus Image Kiosk TT8870

Brands by name

Popular brands

HHP Adaptus Image Kiosk TT8870, Programming Manual

Search results

Summary of Contents for Adaptus Image Kiosk TT8870

Reviews:

Related manuals for Adaptus Image Kiosk TT8870

Brands by name

Popular brands