HHP Adaptus Image Kiosk TT8870 Programming Manual Download Page 62

Page: 62 / 149

5 - 20

Image Kiosk™ TT8870 Programming Guide

Linear Symbologies

UPC-A Check Digit

This selection allows you to specify whether the check digit should be transmitted
at the end of the scanned data or not.

Default = On.

UPC-A Number System

The numeric system digit of a U.P.C. symbol is normally transmitted at the
beginning of the scanned data, but the unit can be programmed so it will not
transmit it.

Default = On.

UPC-A Addenda

This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
Default = Off for both 2 Digit and 5 Digit Addenda.

* On

Off

* On

* 5 Digit Addenda Off

5 Digit Addenda On

* 2 Digit Addenda Off

2 Digit Addenda On

Summary of Contents for Adaptus Image Kiosk TT8870






















































































































































Search results

Summary of Contents for Adaptus Image Kiosk TT8870

Reviews:

Related manuals for Adaptus Image Kiosk TT8870

Brands by name

Popular brands

HHP Adaptus Image Kiosk TT8870, Programming Manual

Search results

Summary of Contents for Adaptus Image Kiosk TT8870

Reviews:

Related manuals for Adaptus Image Kiosk TT8870

Brands by name

Popular brands