HESCH HE 5731 Compact Operating Instructions Manual Download Page 40

Page: 40 / 46

HE 5731 Operating instructions

# 373344, Version 1.5

Options

Display

Cause

Action

The high alarm LED

flashes

The differential pressure ex-
ceeds the set limit



Adjust the set pulse and
pause times



Check the filter element



Check the solenoid
valve, that it is mechani-
cally functioning without
defects or errors



Check the air pressure
system

The low alarm LED

flashes

The differential pressure is
going below the set limit for
longer than 5 min. without
reaching a post-cleaning limit



Adjust the set pulse and
pause times

Post-cleaning is not
working

• no signal at post-cleaning
entry
• precoating function active
• differential pressure does
not exceed the lower
cleaning threshold



Disable precoating

(see chapter 7.5 Enable
/ Disable Precoating

)

Summary of Contents for HE 5731 Compact















































Search results

Summary of Contents for HE 5731 Compact

Reviews:

Related manuals for HE 5731 Compact

Brands by name

Popular brands

HESCH HE 5731 Compact, Operating Instructions Manual

Search results

Summary of Contents for HE 5731 Compact

Reviews:

Related manuals for HE 5731 Compact

Brands by name

Popular brands