background image

11

•  Dark display: When on, the app background colour 

turns from bright to dark

•  Language setting: Here you can set your desired 

language

•  Change bicycle: Here you can disconnect from 

a paired e-bike. This can be relevant if you want 

another rider to use your e-bike and control it from 

their own smartphone app. Two smartphone apps 

cannot be connected to the same e-bike at the 

same time.

•  Cycling data clear: Here you can delete the app 

history

•  Reset: Here you can reset the app to the factory 

settings

Operating the app

The app displays various information about your ride, 

watt consumption and battery charge status. You may 

find it convenient to acquire a smartphone mount for 

your handlebar to have your smartphone placed easily 

visible and accessible at your handlebar.

DANGER! 

Never operate the app while your 

e-bike is in motion as this prevents 

you from carfully paying attention to 

your surroundings which may result in 

an accident which can damage your 

e-bike and cause serious bodily injury.

On the app’s main screen you can monitor the 

following:

•  Bluetooth icon: Shows the Bluetooth connection 

status. When red, the app and motor are not 

connected. When blue, the app and motor are 

connected.

•  Battery icon: Shows the charge status of the 

battery. If the battery is fully charged, the icon 

shows five green bars. When the battery is close 

to being discharged, the icon shows one red 

bar. The number of green bars can vary a little 

depending on riding conditions. For example, 

when riding uphill the number of bars may go 

down by one and then go back up one bar when 

riding downhill immediately after.

•  Speedometer: The number in the middle shows 

your running speed. The green left side of the 

circle shows your relative speed. The red right 

side of the circle shows your relative power 

assist level. ODO in the lower part of the circle 

shows your total distance travelled while the app 

has been connected to the motor without any 

disconnections.

•  AVS: Shows your average speed for your current 

ride.

•  MXS. Shows your maximum speed for your 

current ride.

•  TM: Shows the time passed for your current ride

•  TRIP: Shows the distance travelled for your 

current ride.

•  Power: Shows the running power assist in watts.

•  TEMP: Shows the motor temperature.

•  The buttons Off, Eco, Tour and Sport lets you 

choose your desired power assist level. Please see 

chapter 2 about the motor for more information 

about the power assist settings.

The app can only monitor your ride when open as the 

primary app on your smartphone screen. It is not able 

to keep running in the background if you open and 

use any other app. For example, if you have not turned 

on ‘Bright display’ in the app settings, the app stops 

monitoring your ride if your screen locks according 

to your general smartphone ‘Automatic lock’ settings. 

This is also the case if you make or accept a call on 

the phone. The app will in those instances cease to 

meassure the time span of your ride.

5. Warranty

Hermansen Copenhagen ApS is obliged by law to 

provide a 2 year right of complaint on your e-bike, 

commencing on the date your e-bike was delivered 

or handed over to you relating to any faults or 

defects existing at the time of purchase that reduce 

or void its value or suitability. Regardless of the 

legally prescribed liability for defects, Hermansen 

Copenhagen ApS grants the first owner of the e-bike 

a 25-year guarantee on manufacturing defects on the 

frame, commencing on the date of purchase. In a first 

step there is a claim for supplementary performance, 

in particular repair or replacement. Warranty claims 

only exist for initial faults that were already present at 

the time of handover.

 

Your e-bike battery is a wearing part. The electronic 

components within are subject to the statutory 

warranty of two years. We guarantee that the battery 

still has a capacity of 60% after two years or 500 

charge cycles depending on which occurs first.

 

Damage caused by for example wear, failure to 

maintain and care for the e-bike, crashes, excessive 

strain caused by excess loads, incorrect assembly 

and handling, tuning or any changes or modifications 

to the e-bike is not covered by this warranty. No 

warranty claims can be made if the e-bike is used in 

competitions, jumps or if exposed to extreme strain of 

any other type.

 

The terms described here do not apply to commercial 

use.

Summary of Contents for Bike One













Reviews: