Hemisphere GPS 804-0138-0 User Manual Download Page 41

Page: 41 / 48

AtlasLink User Guide

PN 875-0352-D Rev A4

Chapter 4: Technical Specifications

Table 4-4: Communication specifications (

continued)

Item

Specification

Baud rates

4800 - 115200

Data I/O protocol

NMEA 0183, NMEA 2000*, Hemisphere GNSS binary,

*requires NMEA certification

Bluetooth

Yes. Bluetooth 2.0 (Class 2)

Wi-Fi

Yes

Web UI

Yes. Http://atlaslink (available when connected via WiFi to the AtlasLink
receiver)

Correction I/O protocol

Hemisphere GNSS proprietary, RTCM v2.3 (DGNSS), RTCM v3

(RTK), CMR (RTK), CMR+ (RTK)

Timing output

1 PPS CMOS, active high, rising edge sync, 10 k

Ω

, 10 pF load

Event marker input

CMOS, active low, falling edge sync, 10 k

Ω

, 10 pF load

Memory (Internal)

2GB (non volatile)

Table 4-5: Power specifications

Item

Specification

Input voltage

7- 32 VDC with reverse polarity operation

Power consumption

< 5.4 W nominal GNSS (L1/L2), GLONASS (L1/L2), BeiDou (B1/
B2/B3) and L-band

Current consumption

0.39 A nominal GNSS (L1/L2), GLONASS (L1/L2), BeiDou (B1/ B2/B3) and
L-band

Power isolation

Reverse polarity
protection

Yes

Antenna voltage

Internal antenna

Table 4-6: Environmental specifications

Item

Specification

Operating temperature

-40° C to +70° C (-40° F to +158° F)

Storage temperature

-40° C to +85° C (-40° F to +185° F)

Humidity

95% non-condensing

Shock and Vibration

Mechanical Shock: EP455 Section 5.14.1 Operational Vibration: EP455
Section 5.15.1 Random

EMC

CE (ISO 14982 Emissions and Immunity), FCC Part 15, Subpart B, CISPR
22

Enclosure

IP67

Table 4-7: Mechanical specifications

Item

Specification

Dimensions

15.8 L x 15.8 W x 7.9 H (cm)
6.2 L x 6.2 W x 3.2 H (in)

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for 804-0138-0

















































Search results

Summary of Contents for 804-0138-0

Reviews:

Brands by name

Popular brands

Hemisphere GPS 804-0138-0, User Manual

Search results

Summary of Contents for 804-0138-0

Reviews:

Brands by name

Popular brands