HELVAR 435 User Manual Download | Manualshive

Page: 25 / 31

background image

Helvar 435 BACnet Gateway: User Guide

21

Annex A – Protocol Implementation Conformance Statement (Normative)

(This annex is part of this standard and is required for its use.)

BACnet Protocol Implementation Conformance Statement

Date: 2 September 2016

Vendor Name: Synapsys Solutions Ltd

Product Name: Synapsys SIP

Product Model Number: N/A

Application Software Version: 1.05

Firmware Revision: 0.8.3

BACnet Protocol Revision: 12

Product Description

This software module is used across Synapsys SIP products range and exposes values typically
from Modbus, Mbus or other over BACnet IP.

BACnet Standardized Device Profile (Annex L):



BACnet Operator Workstation (B-OWS)



BACnet Advanced Operator Workstation (B-AWS)



BACnet Operator Display (B-OD)



BACnet Building Controller (B-BC)



BACnet Advanced Application Controller (B-AAC)



BACnet Application Specific Controller (B-ASC)



BACnet Smart Sensor (B-SS)



BACnet Smart Actuator (B-SA)

«
...
23
24
25
26
27
...
»

Summary of Contents for 435
































Reviews:

No comments

Related manuals for 435

Brand: BAB TECHNOLOGIE Pages: 39

UNIGATE IC - Powerlink

Brand: DEUTSCHMANN AUTOMATION Pages: 50

Brand: Pulse Secure Pages: 39

Brand: AES Corporation Pages: 2

IZAR IoT GATEWAY Compact

Brand: Diehl Pages: 4

Brand: THOMSON Pages: 710

Brand: Alpha Technologies Pages: 25

Brand: PREDICTWIND Pages: 16

Brand: Dormakaba Pages: 8

Brand: Xantrex Pages: 80

Brand: ADT Pulse Pages: 6

Brand: Arris Pages: 116

Brand: Technoton Pages: 69

Brand: Anviz Pages: 102

Brand: Sonoff Pages: 2

Brand: XAVI Technologies Corp. Pages: 51

Brand: Sky Microwave Pages: 14

Brand: TAIKO Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands