A89995_A
©
2019 All rights reserved.
1/8
BEST is a trademark of dormakaba USA Inc.
Tools Needed
Herramientas necesarias
Outils nécessaires
Drill Bit
Broca de taladro
Mèche
#2 Phillips
Screwdriver
Destornillador
Phillips N.º 2
Phillips n° 2
Tournevis
A
Gateway
Compuerta
Passerelle
B
(2x)
Antenna
Antena
Antenne
C
Mounting Bracket Assembly
Conjunto del soporte de montaje
Assemblage de support de montage
D
Ceiling Grid Bracket Assembly
Conjunto del soporte de la rejilla del techo
Assemblage de support de l’élément plafonnier
E
(2x)
#6-32 x 3/4" Machine Screw
Tornillo para máquina N.º 6-32 x 19 mm (3/4 pulg.)
Vis mécanique no 6 à 32 filets x 19 mm (3/4 po)
F
#6-19 x 1/4" Retaining Screw
Tornillo de retención N.º 6-19 x 6.4 mm (1/4 pulg.)
Vis de fixation no 6 à 19 filets x 6 mm (1/4 po)
Ethernet Cable
Cable de Ethernet
Câble Ethernet
H
Omni-Directional Antenna Kit
Kit de antena omnidireccional
Kit d'antenne omnidirectionnelle
I
Integrated Portal Gateway Enclosure
Gabinete de compuerta de portal integrado
Enceinte de passerelle avec portail intégré
J
G
AC/DC Power Converter
Conversor de alimentación CA/CC
Convertisseur de secteur CA/CC
1
Wi-Q Gateway Installation Instructions
Instrucciones de instalación de la compuerta Wi-Q
Instructions pour l'installation de la passerelle Wi-Q
Drill
Taladro
Foret
Develop a Site Plan
NOTE:
Powered with 110VAC or with PoE,
PoE class 1 device
NOTA:
Alimentado con 110 V CA o con PoE,
dispositivo de clase 1 PoE
REMARQUE :
Alimenté par 110 VCA ou un dispositif
d’alimentation par Ethernet de classe 1
2
Position Gateways
3
Mount Gateways
A
D
B
(2x)
C
Drop ceiling
installation only
solo para instalación
en techo colgante
installation sur faux
plafond uniquement
Two #6 x 1/4"set
screws included
incluye dos tornillos de fijación
N.º 6 x 6.4 mm (1/4 pulg.)
deux vis de calage no 6 x 6 mm
(1/4 po) sont incluses
Once all the door hardware and controllers have been installed,
you are ready to determine the final placement of the Gateways
using the results from the Wi-Q Site Survey. The Site Survey
helps you determine the number and optimum location of the
Gateways and verify the signal strength before permanently
installing the Gateway hardware. It is important to perform the
Site Survey process as many times as needed to determine the
optimal positions of the Gateways that allow a strong signal
connection to be achieved for all of the locks.
You will need to test the signal strength at all the door locations
near the perimeter of the coverage area as well as any location
where a physical obstruction may cause interference.
Once the optimal location of the Gateway has been determined,
the Gateway may be permanently mounted.
The Gateway can be installed on a variety of surfaces, including:
1. Drop ceiling
2. Wall or rigid ceiling (such as drywall,
concrete, paneling, or similar material)
3. Shelf
4. Electrical box
5. Integrated Portal Gateway (IPG) enclosure
Create a site plan to define the area you want to control and
the appropriate location of the Gateway. The Gateway should
be installed in a centralized location and near a network
connection.
Transmit range from the Gateway to the controller varies
based on the building construction. Site characteristics such as
reinforced concrete walls could interfere or weaken the signal;
open spaces and low interference can increase signal strength.
F
Optional to use
uso opcional
utilisation facultative
J
Optional and
sold separately
opcional y
se vende por separado
facultatif et
vendu séparément
I
E
(2x)
Electrical box/IPG
installations only
solo para instalaciones
en cajas eléctricas/IPG
installations avec boitier
électrique/IPG uniquement
G
uso opcional,
no es necesario si es
alimentado por POE
Optional to use,
not needed if
powered by PoE
utilisation facultative,
non nécessaire si
alimenté par Ethernet
H
no incluido,
requerido
para la instalación
Not included,
required
for install
non inclus,
requis
pour installer
Optional and
sold separately
opcional y
se vende por separado
facultatif et
vendu séparément
BEST Access Solutions
Knowledge Base
https://support.bestaccess.com/hc/en-us/articles/
201179876-Wi-Q-Hardware-Templates-Instructions
