HELVAR 435 User Manual Download Page 24 | Manualshive

Page: 24 / 31

background image

20

Helvar | Data is subject to change without notice.

4.

Protocol Implementation Conformance (PIC) Statement

Helvar’s 435 BACnet Gateway is an OEM product from Synapsys Solutions Ltd and is a variant of the

Synapsys SIP. The following Protocol Implementation Conformance (PIC) statement gives the full
compliance by Synapsys for all variants of the SIP gateway.

The Helvar 435 variant offers a reduced selection of the full BACnet/IP capability that is available from the
SIP. The standard object types supported for the Helvar 435 are: analogue value, analogue input,

analogue output, and binary inputs.

«
...
22
23
24
25
26
...
»

Summary of Contents for 435
































Reviews:

No comments

Related manuals for 435

Brand: Banner Pages: 96

Brand: Yeastar Technology Pages: 11

Touchstone TG1652

Brand: Arris Pages: 44

Brand: Genexis Pages: 5

Brand: Rath Pages: 9

NetPerformer SDM-9220 Series

Brand: Memotec Pages: 146

SBG3500-N Series

Brand: ZyXEL Communications Pages: 10

Brand: H3C Pages: 39

Brand: Nitgen Pages: 36

Brand: SAGEMCOM Pages: 60

Brand: iS5 Pages: 184

Brand: eQ-3 Pages: 44

Brand: Planet Pages: 162

Wine Cap MWDG-ETH

Brand: Capetti Elettronica Pages: 6

Brand: Riello UPS Pages: 14

Brand: BellEquip Pages: 20

Brand: SmartRG Pages: 18

Brand: Shenzhen Seener Wireless Technology Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands