HELVAR 435 User Manual Download Page 27 | Manualshive

Page: 27 / 31

background image

Helvar 435 BACnet Gateway: User Guide

23

Proprietary properties: –

Property range restrictions: –

ANALOG_VALUE

Dynamically creatable: No

Dynamically deletable: No

Optional properties: Description, Reliability, Priority_Array, COV_Increment, Relinquish_Default

Writable properties: Present_Value, Reliability when Out_Of_Service is TRUE, Out_Of_Service
(These are saved in volatile memory; changes are lost after reboot)

Conditionally writable properties: –

Proprietary properties: –

Property range restrictions: –

ANALOG_OUTPUT

Dynamically creatable: No

Dynamically deletable: No

Optional properties: Description, Reliability, COV_Increment

Writable properties: Present_Value, Reliability when Out_Of_Service is TRUE, Out_Of_Service (These
are saved in volatile memory; changes are lost after reboot)

Conditionally writable properties:

–

Proprietary properties:

–

Property range restrictions:

–

BINARY_INPUT

Dynamically creatable: No

Dynamically deletable: No

Optional properties: Description, Reliability

«
...
25
26
27
28
29
...
»

Summary of Contents for 435
































Reviews:

No comments

Related manuals for 435

MultiVOIP MVP210-SS

Brand: Multitech Pages: 36

Brand: Iget Pages: 12

Brand: Cellio Pages: 9

Brand: Raymarine Pages: 84

Brand: ABB Pages: 45

Brand: ABB Pages: 108

Brand: MikroTik Pages: 9

ACCESS MANAGER 3.1 SP1 - ADMINISTRATION

Brand: Novell Pages: 42

Brand: Novatel Pages: 88

Brand: Media Pages: 8

Brand: Gigaset Pages: 8

Brand: ZUORA Pages: 7

Brand: Juniper Pages: 138

Brand: Silicon Graphics Pages: 42

Brand: Alpha Telecom Pages: 43

Brand: SmartRG Pages: 16

DataRoute voice

Brand: Telecom FM Pages: 55

Brand: SmartRG Pages: 158

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands