29
The weekly program is erased when the switch is off.
For example: Setting Monday 1
st
period working time 7:00 to 13:00
Press P
Day EDIT Time/On Time/Off OK
SET OPEN WINDOW (ONLY by remote control)
- Press
to switch on the appliance, heating for a moment
until stability.
- Press to active the open window mode (the light is on).
- Press + or - to set the setting temperature for the open
windows function.
- Press to disable the open window mode (the light
is
off).
The appliance will resume to previous working mode.
During open window mode, if the room temperature drops from about 5°C to 10°C in less than 10
minutes, the appliance will stop working and enter into stand by mode. Press
again to switch on
the appliance.
If open-window mode and weekly timer program simultaneously, if the appliance turn off in weekly time, the
appliance is not turned on. If it already turn on in weekly timer, the appliance working as the setting
temperature under open-window mode.
For example: when window open detection function on, the weekly working time already setting before: it's
Monday morning A.M 9:00--10:00 , desired temperature 28 degree, the window open only working A.M 9:00-
-10:00 , the unit will cut off when temperature reduce to 23
°C
or more lower . Other time, the unit not
working, just in standby.
Switch off:
To stop the operation of the device, press the function switch (Fig.
Attention: the device is still ready for use.
In order to disconnect the unit from the mains, press the main power switch (F) to position " 0 " on the
device and unplug the plug from the socket-outlet.
Battery:
The remote control is to use with battery (CR2025) (3V) if no battery is included. If battery included and if available,
remove the transparent plastic film from remote control door (A, B, C). When the battery is out of power please
change the battery as Fig. 4
Fig. 4
30
Note: Please follow the instructions of your designated local disposal company for battery disposal.
Overheating protection:
To prevent damage and risks due to overheating, an additional built-in overheating safety device
protects the heater against overheating and cuts off the heating element automatically.
•
In that case, the heating element is ready for operating again after a short cooling-off phase.
•
If the safety device again switches off, please check if anything is obstructing in the surrounding
of the air flow.
•
Should it come to repeated switches off, please remove the mains plug from the wall socket and get in contact
with your trader or the customer service of the manufacturer.
Please pay attention to the guarantee conditions.
CLEANING AND MAINTENANCE
•
First, switch off the device, pull out the power plug from electrical outlet and let the heater cool down.
•
Clean the air inlet and outlet grilles regularly from dust and dirt (by normal use at least twice a year) with a
vacuum cleaner, use the vacuum brush attachment..
•
Use the soft cloth to wipe the dust from enclosure. Do not use water! Never immerse the
appliance or power cord, plug in water or other liquids! Danger to life!
•
Do not use any abrasive or caustic cleaning agents! Do not use any flammable cleaning agents e.g. petrol or
spirit for cleaning the device, as they will damage the heater or can cause a fire hazard.
•
If the appliance is not going to be used for some time, it should be protected against excessive dust
and dirt.
•
Keep the original box in which the heater was packed. Clean the heater according to the instructions for
Cleaning. Pack the heater in the original box and store it in a cool, dry place.
Technical Details:
Type
Accessories
Voltage
Frequency
heating
power
Measure
KPF 2001 B
Remote
control
220-240V~
50 Hz
1000W
2000W
56,5x19,5x10,5cm
Guarantee:
•
Please see the instruction in the guarantee section if problems occur with the fan heater. There is a guarantee
of two years. During this period, faulty components will be repaired or replaced free of charge, if the fault is due
to a manufacturing defect. In this case, consult the retailer where you have purchased the appliance. Please
don’t try to open or repair the fan heater yourself as this will void the guarantee and could also result in
damage to property and injury to people.
•
Every intervention in the unit for the change of the original condition leads inevitably to the loss of the
guarantee claim.
CE-marking:
The CE mark shows that the unit meets all essential Directives "Electromagnetic Compatibility"
(Directive 2014/30/EU), “Low Voltage Directive” (Directive 2014/35/EU) and directive “RoHS” (2011/65/EU).
