manualshive.com logo in svg

HEIDELBERG HRC, Installation Instructions Manual

Share
Download
HEIDELBERG HRC Installation Instructions Manual Download Page 24

 

HRC Installation Instructions Vers. 001 

24 

HRC Color+FA 
Connect all three plugs (SDO cable, Camera color
mono) to the power control unit as shown in the 
illustration below.  Secure the plugs against an involuntar
disconnection by tightening them in place. 
 
 
 
 
 
 

 

Connect the foot switch to the socket „foot switch“. 

 

Check if all units are correctly connected, then connect the isolating transformer to the 
mains and switch it on.

 

NOTE:  

The line voltage adjusts automatically to the local power outage.   

 

4.4.3  12 V - Output 

The 12 V output is available to connect further electrical DC voltage loads that have a maximum of 
500mA (i.e. fixation lamps ). 

 

 
 

4.5 

Software Protector (Dongle) 

The software protector (dongle) must be inserted into the 
parallel or USB port of the computer. Please note that the 
software protector (dongle) must remain connected at all 
times while operating the HRC.  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

, Camera 

y 

Summary of Contents for HRC








































Reviews:

No comments

Brands by name

Popular brands

Load more brands