Heatilator NASIM Manual Download Page 7 | Manualshive

Page: 7 / 32

Heatilator NASIM Manual Download Page 7

09-02

7

30532 Rev D

NASIM REAR DIRECT VENT DECORATIVE GAS APPLIANCE

E. VENTING

1. HORIZONTAL TERMINATION (using

supplied venting)

This kit is supplied with a standard vent kit that will meet

the majority of installations for this NASIM appliance. This

kit consists of a 6 - 9 slip section, a wall shield, and a

termination cap. A typical installation is diagrammed in

Figure 5.

WARNING - RISK OF FIRE!

Air space clearances must be maintained at all times.

Horizontal termination (using supplied venting) - see below.

Horizontal termination (using additional venting) - see page 8.

Vertical termination - see page 11.

Figure 5 - Typical Installation

WARNING - RISK OF FIRE!

The horizontal run of vent must have a 1/4 rise for

every 1 ft. of run towards the termination. Never al-

low the vent to run downward. This could cause high

temperatures and may present a fire hazard.

WARNING - RISK OF FIRE!

If you have chosen horizontal termination, be sure

there are no present nor future obstructions from

trees, bushes, snow drifts, etc.

a. Installing the Interior Wall Shield

Frame a hole in a combustible wall for an interior

wall shield as shown in Figure 6. This shield

maintains minimum clearances and prevents cold

air infiltration.
The termination cap height must meet all local and

national codes and not be easily blocked or

obstructed. If the material being penetrated is of

noncombustible materials, a 9 diameter hole is

acceptable.
Secure the shield to the framing as shown in

Figure 6.

Figure 6 - Interior Wall Shield

All manuals and user guides at all-guides.com

«
...
5
6
7
8
9
...
»

Summary of Contents for NASIM

































Reviews:

No comments