manualshive.com logo in svg

Heatilator NASIM, Manual, Page: 6 / 32

Share
Download
Heatilator NASIM Manual Download Page 6

30532 Rev D

6

09-02

NASIM REAR DIRECT VENT DECORATIVE GAS APPLIANCE

C. FRAMING

Figure 3 shows a typical framing of this appliance using combustible materials. Figure 4 shows the mantel heights for mantel

projections. All required clearances to combustibles must be adhered to.

Figure 3 - Framing

Figure 4 - Mantel Heights

CAUTION:

Wear gloves and safety glasses for protection.

CAUTION:

Provide  adequate  clearances  around  the  air

openings  into  the  combustion  chamber  and

adequate accessibility clearances for servicing and

proper operation.

D. SETTING THE APPLIANCE

POSITIONING THE APPLIANCE

This appliance may be placed on a smooth combustible or noncombustible continuous, flat surface. When the appliance

is installed directly on carpeting, tile or other combustible material other than wood flooring, the appliance shall be

installed  on  a  metal  or  wood  panel  extending  the  full  width  and  depth  of  the  appliance.  Slide  the  appliance  into

position and level the appliance from side-to-side and front-to-back. Shim with noncombustible material as necessary.

Secure the appliance by bending out the nailing flanges on each side of the appliance and nail to framing. The nailing

flanges have been positioned 5/8 inch back from the front of the appliance to allow the addition of drywall.

WARNING!

To prevent contact with sagging or loose insulation, the appliance must not be installed against vapor barriers

or exposed insulation. Localized overheating could occur and a fire could result.

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for NASIM

































Reviews:

No comments