background image

01/04

15

CALIBER DESIGNER SERIES

FOR YOUR SAFETY

READ BEFORE OPERATING

H. IGNITION

To determine whether your appliance is an intermittent pilot ignition or a standing

pilot ignition, open the control access panel to examine the wiring system. If your

system has a red ignitor button as shown in Figure 18, you own a standing pilot

ignition appliance. If no red ignitor button is present, you own an intermittent pilot

ignition  appliance.
You may also check the rating label located on the inside of the control access

panel to determine ignition type.

Figure 18

Standing Pilot Ignition

1. Intermittent Pilot Ignition Appliances

WARNING! 

If you do not follow these instructions exactly, a fire or explosion may result causing

property damage, personal injury or loss of life.

A. This  appliance  does  not  have  a  pilot.  It  is  equipped  with  an  ignition  device  which  automatically  lights  the

burner. Do not try to light the burner by hand.

B. BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electric switch; do not use any phone in your building

•

Immediately  call  your  gas  supplier  from  a  neighbor’s  phone.  Follow  the  supplier’s  instructions.

•

If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to turn the manual shutoff valve.. Never use tools, If the lever or knob will not move by hand,

don’t  try  to  repair  it  -  call  a  qualified  service  technician.  Force  or  attempted  repair  may  result  in  a  fire  or

explosion.

D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to

inspect the appliance and to replace any part of the control system and any gas control which has been under

water.

LIGHTING  INSTRUCTIONS

1. STOP! Read the safety information above on this label.

2. Turn wall switch to the “OFF” position.

3. This appliance is equipped with an ignition device which automatically lights the burner. Do not try to light

burner by hand.

4. Wait five minutes to clear out any gas. If you then smell gas, STOP! Follow “B” in the safety information above

on this label. If you don’t smell gas, go on to the next step.

5. To turn on burner, turn on all electric power to this appliance.

6. If the appliance will not operate, follow the instructions “TO TURN OFF GAS TO APPLIANCE” and call your

service technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE

1. Turn off the wall switch.

2. Open the control access panel.

3. Turn the gas line to the CLOSED position. Do not force.

4. Close  the  control  access  panel.

I. LIGHTING INSTRUCTIONS

Summary of Contents for CALIBER DESIGNER B-VENT SERIES

























Reviews: