Heartland VALUE Series Assembly Manual Download

Page: 91 / 103

LEFT

DOOR

Mark and pre-drill holes for screws. Install bolt with screws supplied.

Drill 5/16" (7,9 mm) hole deep enough for bolt to slide into.

Place bolt on

in open position with bolt end 3/8" (9,5 mm) down from frame.

Bolt is open when loop is contacting base

(Fig A)

Fig. A

Fig. B

Place bolt on

in open position with bolt end 1/2" (12,7 mm) up from floor.

Bolt is open when loop is connecting base

(Fig. B)

Mark and pre-drill holes for screws. Install bolt with screws supplied.

Drill 5/16" (7,9 mm) hole deep enough for bolt to slide into.

5/16" (7,9 mm)
drill for bolt:
1" (2,5 cm) deep.

1/2"

(12,7 mm)

OPEN POSITION

Spring is loose.

OVER DOOR

FRAME

FLOOR

Loop contacts

base

Loop contacts

base

OPEN POSITION

Spring is loose.

3/8" (9,5 mm)
with bolt
in open
position.

PRE-DRILL
(4) HOLES

BEGIN

PARTS REQUIRED:

DOOR HARDWARE

5/16" (7,9 mm) Drill Bit

3/4" (1,9 cm)

Summary of Contents for VALUE Series








































































































Search results

Summary of Contents for VALUE Series

Reviews:

Related manuals for VALUE Series

Brands by name

Popular brands

Heartland VALUE Series, Assembly Manual

Search results

Summary of Contents for VALUE Series

Reviews:

Related manuals for VALUE Series

Brands by name

Popular brands