Heartland SOHO MODERN Assembly Manual Download

Page: 67 / 71

• Follow directions provided by manufacturer and these instructions.

SHINGLES

- NOT INCLUDED -

NEVER DRIVE FASTENERS INTO OR ABOVE SEALING STRIPS.

Familiarize yourself with a 3-Tab Shingle.

SHINGLE NAIL PATTERN

(2,5 cm)

NAILS

Sealing Strip

(2,5 cm)

1/2"

(1,3 cm)

Full Rain Slot

Half A Rain Slot

Notch

Install first starter row upside down, color up and flush to drip edge at bottom of roof panel. Use (4) nails per shingle.

Starter row must be straight and level all the way across with lower edge of roof deck.

Begin where indicated on image below, install first row of shingles with notch flush with drip edge.

Drip Edge

Notch

BACK OF SHED

START HERE

BACK OF SHED

TABS UP

BEGIN

Shingle overlaps

roof decking.

(4) Nails

Flush to drip edge.

Flush with starter row.

1" (2,5 cm)

Flush to drip edge.

DOOR

BEGIN

Summary of Contents for SOHO MODERN








































































Search results

Summary of Contents for SOHO MODERN

Reviews:

Related manuals for SOHO MODERN

Brands by name

Popular brands

Heartland SOHO MODERN, Assembly Manual

Search results

Summary of Contents for SOHO MODERN

Reviews:

Related manuals for SOHO MODERN

Brands by name

Popular brands