Heartland PASADENA PAVILION 10x12 Assembly Manual Download Page 34

WARRANTY
Backyard Storage Solutions, LLC warrants the following:

1. 

Every product is warranted from defects in workmanship and manufacturing for one year.

2. 

All hardware and metal components are warranted for two years.

3. 

Trim is warranted for 10 years.

4. 

Waferboard siding and sheathing is warranted for two years.

5. 

SmartSide™ siding is warranted for 10 years on all Backyard Storage Solutions, LLC series buildings and 15 years on all 
Premier Series buildings.

6. 

Timber series buildings’ siding and trim are warranted for 10 years.

7. 

Solar Shed windows are warranted for 1 year.

8. 

Cedar lumber is warranted for 15 years.

9. 

(ProWood TM, MicroShade TM Pavilion) All wood components have a Limited Lifetime Warranty.

 

 

• Treated Wood will be replaced if wood becomes structurally un t due solely to damage caused by fungal decay or   

 

  termites.

10. 

 (ProWood TM, MicroShade TM Pavilion) MicroShades Stain Fade Resistance has a two year Limited Warranty.

 

 

* Wood treated with the MicroShades pigment color system which sustains “signi cant color changes” will be replaced.

 

 

* “Signi cant color changes” to wood components is at the discretion of Backyard Storage Solutions, LLC and  

                  

 

requires proof in the form of photographs or inspection by Backyard Storage Solutions, LLC. Wooden components  

                                                

 

may have imperfections such as checks and knots. These are natural blemishes and imperfections which are inherent  

 

to wood. The imperfections not resulting in structural failure are not covered under this warranty.

Backyard Storage Solutions, LLC will repair, replace or pay for the affected part.  In no event shall Backyard Storage Solutions, LLC pay 
the cost of labor or installation or any other costs related thereto.  All warranties are from date of purchase.  If a cash refund is paid on an 
affected part, it will be prorated from the date of purchase.

CONDITIONS
The warranty is effective only when:

1. 

The unit has been erected in accordance with the assembly instructions. 

2. 

The unit has been properly shingled and painted or stained and reasonably and regularly maintained thereafter.

3. 

The failure occurs when the unit is owned by the original purchaser.

4. 

Backyard Storage Solutions, LLC  has received the warranty registration card within thirty (30) days of purchase and 
noti cation of the failure in writing within the warranty period speci ed above.

5. 

Backyard Storage Solutions, LLC  has had reasonable opportunity during the sixty (60) days following receipt of noti cation 
to inspect and verify the failure prior to commencement of any repair work.

REQUIREMENTS
Storage Buildings & Playhouses
To validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit; shingle the roof and paint or 
solid-colored stain the siding using 100% acrylic latex exterior product with a minimum of two (2) coats within thirty (30) days of assembly; 
caulk above all doors and all horizontal and vertical trim boards; paint and seal all exposed edges, sides and faces of SmartSide™ and 
waferboard siding to include all exterior walls and all sides and all edges of doors.  

Gazebos and Cedar Pergolas
To validate your warranty, it is necessary to properly maintain your Backyard Storage Solutions, LLC unit.  This includes treating all of 
the exposed cedar and pine surfaces on your gazebo or pergola with an exterior grade wood preservative, an exterior oil-based semi-
transparent stain, an acrylic latex exterior paint or an acrylic latex solid color exterior stain within 30 days of assembly and as needed 
thereafter to maintain your warranty.

Keep vegetation trimmed away from building and make sure siding panels and trim do not come in contact with masonry or cement.  The 
minimum ground clearance for siding must be one half inch (1/2 inch) from concrete slab or two and one half inches (2 ”) from the ground 
when building is erected or constructed on a treated wood  oor kit.  Water from sprinklers must be kept off unit.  In no event will Backyard 
Storage Solutions, LLC be responsible for any indirect, incidental, consequential or special damages nor for failure(s) that are caused by 
events, acts or omissions beyond our control including, but not limited to, misuse or improper assembly, improper maintenance (which 
eventually leads to rot or decay) and acts of God.  Backyard Storage Solutions, LLC will not be held responsible for any labor costs 
incurred to construct your unit.  This warranty gives you certain speci c rights that vary from state to state.

CLAIM PROCEDURE
To make a claim under this warranty, you can either call (888) 827-9056 or prepare a letter.  Please have ready the information below 
when you call or include the information when writing:

1. 

The model and size of the product.

2. 

A list of the part(s) for which the claim is made.

3. 

Proof of purchase of the item, as shown on the original invoice.

4. 

Run code, as listed on the yellow warranty card enclosed in the product package.

Mail the above information to:

 

Backyard Storage Solutions, LLC

 

Attn:  Customer Service

 

1000 Ternes Drive

 

Monroe, MI 48162 

 

 

     

*WARRANTY TERMS MAY VARY OUTSIDE THE U.S.A.

IMPORTANT:  This is your warranty certi cate.

 

 

 

Please complete and mail your warranty card to properly validate your warranty. 

              

 

 

 

 

 

 

 

 

ldr: 

 

09/04/09

Limited Conditional

Warranty *

Summary of Contents for PASADENA PAVILION 10x12



































Reviews: